Izdelki za cc150s fo 2v 2c (5)

The CryLaS Q series lasers are diode-pumped solid-state lasers (DPSS lasers) based on a microchip design. This consists of an Nd:YAG resonator with a directly coupled saturable absorber which works as a passive Q-switch. The compact housing and easy operation make the lasers an optimum light source for applications that require minimal housing dimensions with highest performance. Based on the 1064 nm fundamental, harmonics are generated using non-linear (NLO) crystals that allow a wide spectrum of laser wavelengths from 1064 nm to 213 nm. The FQSS213-Q4 laser emits pulses with approximately 1 ns pulse width at 213 nm, and can be modulated from single shot to 1 kHz. The pulse energy is 2.5 µJ. CryLaS lasers impress with their easy installation, service-free operation and long service life. This makes them ideal for OEM applications and demanding laboratory setups. Wavelength:213 nm Pulse energy:2.5 µJ Peakpower:2.5 kW Pulse Width:1 ns Average Power:2.5 mW Repetition Rate:1 kHz Beam diameter:< 0.45 mm Spatial Mode:TEM00 Application:Holography, engraving, photo acoustics, LIBS, mass spectroscopy, photo luminescence

In der Leistungselektronik im allgemeinen, speziell in niederinduktiven Zwischenkreisen höherer Spannungen sowie auch in Entladeschaltungen ist die Forderung nach niederinduktiven Kondensatoren mit Problemen verbunden: Traditionelle Hochspannungskondensatoren sind mit öl gefüllt, und die für die Luft- und Kriechstrecken großzügig auszulegenden Anschlussisolatoren wie auch der interne Sicherheitsmechanismus tragen wesentlich zur Eigeninduktivität des Kondensators bei. Basierend auf jahrzehntelanger eigener Erfahrung bei der Metallisierung von Kondensatorfolien hat ELECTRONICON unter Nutzung spezieller Metallisierungsarten eine Reihe von Hochspannungskondensatoren in selbstheilender Technologie geschaffen. Trotz der hohen Spannungsnennwerte wird die E51 Reihe in trockener Technologie und ohne aufwändige Anschlüsse gefertigt. Das Kondensatorelement im Inneren des Bechers aus selbstverlöschendem Kunststoff ist in PUR-Harz vergossen.

LED Anzeige zur Visualisierung der Emissionsersparnis an CO2 durch eine bestehende Biogasanlage. Das Layout der Scheibenfolierung erfolgt nach Kundenvorgabe. Die aktuellen Werte werden per ModBus-Protokoll vollautomatisch aus dem Leitrechner der Anlage abgerufen und dargestellt. Anwendungsbereich:outdoor Schrifthöhe:175mm max. Leseentfernung:ca. 70-80m LED Farbe:Rot Ansteuerung:Ethernet / ModBus

The CryLaS Q series lasers are diode-pumped solid-state lasers (DPSS lasers) based on a microchip design. This consists of an Nd:YAG resonator with a directly coupled saturable absorber which works as a passive Q-switch. The compact housing and easy operation make the lasers an optimum light source for applications that require minimal housing dimensions with highest performance. Based on the 1064 nm fundamental, harmonics are generated using non-linear (NLO) crystals that allow a wide spectrum of laser wavelengths from 1064 nm to 213 nm. The FQSS213-Q1 laser emits pulses with approximately 1 ns pulse width at 213 nm, and can be modulated from single shot to 20 kHz. The pulse energy is 0.05 µJ. CryLaS lasers impress with their easy installation, service-free operation and long service life. This makes them ideal for OEM applications and demanding laboratory setups. Wavelength:213 nm Pulse energy:0.05 µJ Peakpower:0.05 kW Pulse Width:1 ns Average Power:0.75 mW Repetition Rate:20 kHz Beam diameter:< 0.4 mm Spatial Mode:TEM00 Application:Holography, engraving, photo acoustics, LIBS, mass spectroscopy, photo luminescence

The PK16™ capacitor can be universally used for the assembly of low inductance DC buffer circuits and DC filters; with its high energy density it can replace banks of series-connected electrolytic capacitors as well as large film capacitors in rectangular cases. The capacitance in a DC buffer circuit must be sufficiently sized to both handle and smoothen the occurring ripple currents. The traditional use of series-/parallel-connected electrolytic capacitors offered large capacitance at seemingly low cost, however the low cost per microfarad is countered by the very low current strengh, the high sensitivity to voltage and current surges, as well as a substantial risk of failures in the field, resulting in high maintenance cost. Our advanced know-how in special capacitor film coating and many years of practical experience in designing and manufacturing capacitors have allowed us to develop our PK16™ range with high capacitance density.