Izdelki za cevasti grelniki (18)

Schultze RiRo heaters are your solution for industrial and commercial heating appliances: dust- and watertight, corrosion-resistant, flexible and uncomplicated to install. Suitable for damp locations and rough industry environment, for reliable and efficient heating – often unnoticed, but indispensable. The construction of RiRo-nta is identical with RiRo-nt except for the fact that heating power can be steplessly regulated by our built-in thermostat. It keeps the temperature of your choice constant between +5°C and + 30°C or just protects your room from frost. The red signalling light shows when power is on. Power:500W - 1000W Voltage:230 V Lenght:1040mm - 1840mm Protection mode:IP66 / IP67

Screw-in Tubular Heaters are the standard solution for all heating processes with liquids or gas. The heater is installed in a tank or a tube system by the G1½" screw fitting. The IP54 connection head, fitting and tubular heater consists of stainless steel. The tube sheath material 1.4529 is resistant to sulphite, phosphors and hydrochloride media. Type:without controller and limiter Type:with controller (adjustable from 30 ° to 85 °C, freezing protection at 7 °C) Type:with limiter (adjusted to 110 °C) Type:with controller-limiter-combination

Rechteckig [mm]: 6 x 6 8 x 8 Rund [Ø mm]: 3,0 4,0 5,0 6,5 8,5 10,0 16,0 Länge: max. 250 V Spannung: max. 10 W/cm² Weitere Infos: siehe unten Rechteckig [mm]: 6 x 6 8 x 8 Rund [Ø mm]: 3,0 4,0 5,0 6,5 8,5 10,0 16,0 Länge: max. 250 V Spannung: max. 10 W/cm² Leistungsdichte: max. 300˚C Messing max. 500°C Edelstahl Manteltemperatur: max. 750˚C • gerade oder individuell gebogen • mit ein- oder zweiseitigem Anschluß (D: 8,5 oder 10,0 mm) • verschiedene Anschlußoptionen • mit leicht verformbarem Mantel für die individuelle Anpassung • unterschiedliche Mantelmaterialien • als Rippenrohrheizkörper lieferbar

Standardrohre mit Ø8,5 und Ø10,2 sind mit gewundener Rippe erhältlich. Das Heizelement kann zwei- bis dreimal stärker belastet werden als ein glatter Rohrheizkörper. Durch Anbringen von Kühlrippen an einem gewöhnlichen Rohrheizkörper erhält man eine wesentlich größere Oberfläche für die Wärmeabgabe. Daher eignet sich der Heizkörper gut für Bereiche, in denen aus Sicherheitsgründen eine niedrige Oberflächentemperatur erforderlich ist.

energieeffiziente Heizstrahler für umweltfreundliches und schadstofffreies Heizen im Innen- und Außenbereich - Infrarotheizstrahler - Terrassenheizer - mobile Heizgeräte Heiz- und Infrarotstrahler sorgen im Handumdrehen für eine angenehme, wohlige Wärme. Genau das Richtige in der kalten Jahreszeit. Zuverlässige und sichere Geräte für den Innen- und Außenbereich - egal ob moderner Infrarot-Stehtisch oder mobiler Terrassenheizstrahler - in unserem Sortiment finden Sie genau das Richtige!

Hochleistungsfeuer

Über die Fertigungsschritte Schweißen, Zerspanen und Lackieren verfügen wir im Haus, so dass wir Schweißkonstruktionen einbaufertig liefern können. Beispiele hierfür sind Filtergehäuse, Maschinenfundamente, Rahmen, Konsolen, Roboter-Laufwagen und Vorrichtungsgestelle bis 10 t Stückgewicht. Als Schweißfachbetrieb nach DIN 18800-7 mit Großem Schweißnachweis Klasse E, Zertifizierung nach EN 1090 EXC 3 und ISO 3834-2 stellen wir die Qualität mit erfahrenem, geprüftem Personal und den üblichen QS-Maßnahmen sicher. Wir verarbeiten überwiegend Kohlenstoffstähle und austenitische Chrom-Nickel-Stählen, aber auch Sonderwerkstoffe. Eine Übersicht über Werkstoffe, die wir verschweißen können, finden Sie hier.

Material: Edelstahl; Lotmaterial: Silber; Unsere Dienstleistungen: Rohrbiegen, Hartlöten

Bei Einbau von Schalldämpfern in Rohrleitung - Systemen spricht man in der Regel von Rohrschalldämpfern. Hierdurch können turbulente Strömungen geglättet werden.

Spiralgewickelte Papphülsen, innen und außen Aluminiumbeschichtet für verschiedene Anwendungsbereiche. Wir produzieren individuell, den jeweiligen Anforderungen entsprechend, sprich: die maßgeschneiderte Hülse.

Square stainless steel tubular heaters BASE-flex (1.4541) are a reliable industry standard for the use in heating platens and manifolds. In contrast to traditional tubular heaters with a round section which have to be bent by machines, square BASE-flex can be fitted into any rectangular groove with simple hand tools. Moreover, the square shape results in a bigger heat emitting area of up to 80% compared with a corresponding round section. Finally, the easy manual mounting saves the usually high technical expenditure for casting-in / soldering / cementing of bent round tubular heaters. A soft version of the BASE-flex, the NICKEL-flex (2.4068) is available as special execution. Due to the soft, easy to form nickel material, the NICKEL-flex is suitable for manual mounting with hand tools in round sections, too. Furthermore, Nickel has a better capability to conduct heat compared with stainless steel. Wattage:+ 5% - 10% Resistance:+ 10% - 5% dielectric strength:1500 V Insulation (cold 1000 V DC):> 10 MΩ Leakage current (cold):< 0,5 mA Maximum working temperature :750 °C Length tolerance:± 2% (min. ± 5 mm)

Schultze RiRo heaters are your solution for industrial and commercial heating appliances: dust- and watertight, corrosion-resistant, flexible and uncomplicated to install. Suitable for damp locations and rough industry environment, for reliable and efficient heating – often unnoticed, but indispensable. With the built-in three step switch heating power can be adjusted according to actual requirements. This helps saving energy! Step I 1/3 of heating power Step II 2/3 of heating power Step III 3/3 of heating power Power:1000W - 3000W Voltage:230 V lenght:640mm - 1440mm Protection mode:IP66 / IP67

Schultze RiRo heaters are your solution for industrial and commercial heating appliances: dust- and watertight, corrosion-resistant, flexible and uncomplicated to install. Suitable for damp locations and rough industry environment, for reliable and efficient heating – often unnoticed, but indispensable. With these heaters the excess temperature touching the top of the fins does not exceed 67K (difference of 67°C to room temperature). Power:500W - 1000W Voltage:230 V Lenght:1040mm - 1840mm Protection mode:IP66 / IP67

Schultze RiRo heaters are your solution for industrial and commercial heating appliances: dust- and watertight, corrosion-resistant, flexible and uncomplicated to install. Suitable for damp locations and rough industry environment, for reliable and efficient heating – often unnoticed, but indispensable. Universal features: for power types 1000 W to 3000 W the connection can be fitted with either 230 V or 400 V 3(N) ~. On request: for special applications all types are available in special voltages or different high-grade steel qualities, e.g. for food- or off-shore-industry. Power:500W - 6000W Voltage:230/400V 3(N) lenght:440mm - 2640mm Protection mode:IP66 / IP67

Schultze RiRo heaters are your solution for industrial and commercial heating appliances: dust- and watertight, corrosion-resistant, flexible and uncomplicated to install. Suitable for damp locations and rough industry environment, for reliable and efficient heating – often unnoticed, but indispensable. The heating power is steplessly adjustable and the thermostat keeps your chosen temperature constant. Choose either frost protection or your temperature between + 5°C and + 30°C. The red signalling light shows when power is on. Power:500W - 3000W Voltage:230 V lenght:440mm - 1440mm Protection mode:IP66 / IP67

Schultze RiRo heaters are your solution for industrial and commercial heating appliances: dust- and watertight, corrosion-resistant, flexible and uncomplicated to install. Suitable for damp locations and rough industry environment, for reliable and efficient heating – often unnoticed, but indispensable. The heater RiRo-fa is identical with type RiRo-f, but additionally heat transfer can be controlled steplessly by our built-in thermostat. According to your needs the heater will keep the room frostprotected or the temperature will be kept constant at your choice between + 5°C and + 30°C. Applicable for rooms with risk of fire. Max. 115°C on top of the fins. Power:120W - 1200W Voltage:230 V Lenght:440mm - 1840mm Protection mode:IP66 / IP67

Schultze RiRo heaters are your solution for industrial and commercial heating appliances: dust- and watertight, corrosion-resistant, flexible and uncomplicated to install. Suitable for damp locations and rough industry environment, for reliable and efficient heating – often unnoticed, but indispensable. RiRo-F for rooms with fire risk: the economic choice for rooms where a “full range” heating is not needed, e.g. to protect your rooms or your valuable facilities against frost. To keep below the reduced surface temperature of 115°C we chose appropriate power layout. Max. 115°C on top of the fins. Power:120W - 1200W Voltage:230/400V 3(N) Lenght:440mm - 1840mm Protection mode:IP66 / IP67

Finned Tubular Heaters are the ideal solution for air or gas flow heating processes. The ribs enlarge the heat-releasing surface significantly. Basis of the finned tubular heaters are our 8.5 mm tubular heaters. The outer diameter of the fins is 28 mm. The elements can be delivered straight, U-shaped or circular (special design on request). Tubular heater as well as fins are made of stainless steel, the standard for the tube is 1.4828 (other materials possible as in chapter Round Tubular Heaters), the fins are normally made of 1.4301 (1.4571 on request). Terminations for finned heaters::6,3 mm blade terminal Terminations for finned heaters::M4 threaded pin Terminations for finned heaters::With fibreglass leads