Izdelki za euro plastika ltd (11)

Syntech Poliurea Primer – Epoxy Metal: Dvokomponentni epoksidni premaz specifičan za metalne površine

Syntech Poliurea Primer – Epoxy Metal: Dvokomponentni epoksidni premaz specifičan za metalne površine

Syntech Poliurea Primer – Epoxy Metal Syntech Poliurea Primer – Epoxy Metal is a two-component primer based on epoxy resins free from solvents, used to promote adhesion, as a surface sealant for concrete, applied as a substrate for works with polyureas on metal surfaces and epoxy and polyurethane coatings. Adhesion promoter, surface sealant for concrete, to be applied as a substrate for works with polyureas on metal surfaces and epoxy and polyurethane coatings. The application must take place on a dry and degreased surface; the substrate must not have crumbly or detached parts and with a degree of humidity that must not exceed 5%. Preparation of the substrate may require some types of mechanical action: Smoothing, bush-hammering, shot peening, hydro-washing. Other mechanical actions that can make the support suitable. The individual components must be mixed carefully until a homogeneous mass is obtained. The material can be applied by roller, brush or spray by means of special airless machines, even in two coats. The temperature of the support must always be at least 3°C higher than the dew point temperature. Minimum application temperature +5°C, maximum temperature +35°C. Approximately 0,20 kg of Syntech Poliurea Primer – Epoxy Metal for every square metre of surface to be treated. Can 10 kg [A] - Can 5 kg [B] - Kit: 1 Can 10 kg [A] + 1 Can 5 kg [B]
Prevozni in logistični servis

Prevozni in logistični servis

ARTIMAS est une société polonaise spécialisée dans une gamme de services de transport routier entre l'Europe et l'Asie / les pays de la CEI et propose diverses options de transport: bâchés, conteneurs, charges surdimensionnées, matériaux en vrac et transport réfrigéré. Nous offrons des solutions d'envoi complets et Express. ARTIMAS est active sur le marché depuis 2010, et opère depuis la Pologne et l'Asie. En Pologne, vous pouvez nous trouver à Varsovie, Aleksandrówka, Biała Podlaska et Olkusz. Nous sommes en mesure de satisfaire tous vos besoins en transport et logistiques. N'hésitez pas à nous contacter pour plus d'informations.
Barvna PPF folija

Barvna PPF folija

Film de protection de couleur permettant de changer la couleur d'un véhicule tout en aillant la protection du film PPF (auto cicatrisation, brillance, protection UV, protection film routier...
SILIKONSKO VLIVANJE 22SH.A 50KG - Izdelki za Silikonsko Vlivanje

SILIKONSKO VLIVANJE 22SH.A 50KG - Izdelki za Silikonsko Vlivanje

ZA 22 SPRAY, est un silicone RTV par addition bi-composant (base et catalyseur) qui vulcanise à température ambiante. Indiqué pour la duplication de modèles avec peu de contre- dépouilles et pour applications sur des surfaces verticales. -> Domaines d'application Fabrication de moule et restauration pour applications verticales. -> Caractéristiques Unité de vente : kit de 25kg base + 25kg catalyseur Minimum de vente : 1 kit Dureté : 22 Shore A. Dosage en poids : 1 / 1 Temps de travail : 12 à 18mn à 23°C
Belzona 5231 (SG Laminat)

Belzona 5231 (SG Laminat)

Zweikomponenten-Epoxidharzbeschichtung zum Schutz von Fußböden mit ausgezeichneter Beständigkeit gegen Chemikalien und Abrieb sowie Rutschbeständigkeit aufgrund der Zumischung eines langlebigen Zuschl
Papir za toplotni prijenos

Papir za toplotni prijenos

I nastri di carta per trasferimento termico sono essenziali per le macchine di misurazione della pelle, offrendo una soluzione versatile e affidabile per le esigenze di stampa. Disponibili in una varietà di colori tra cui bianco, nero, argento, arancione e oro, questi nastri garantiscono una stampa chiara e precisa su tutte le superfici. La loro qualità superiore assicura che ogni stampa sia nitida e durevole, rendendoli ideali per l'uso in ambienti industriali esigenti. Con una gamma completa di dimensioni disponibili, questi nastri si adattano perfettamente a qualsiasi macchina di misurazione della pelle, garantendo una compatibilità senza problemi e una facile installazione. La loro resistenza e affidabilità li rendono una scelta eccellente per le aziende che cercano di ottimizzare i loro processi di misurazione e stampa. Inoltre, l'ampia selezione di colori consente una personalizzazione unica, permettendo alle aziende di distinguersi con stampe vivaci e accattivanti. Scegliendo i nastri di carta per trasferimento termico, le aziende possono migliorare l'efficienza operativa e garantire risultati di alta qualità in ogni progetto.
ELASTOSAL Metalni Temelj

ELASTOSAL Metalni Temelj

Universeller Haftvermittler für Kaltverklebung oder Heißvulkanisation von Metall mit Gummi oder Polyurethan z.B. bei Verschleißschutzauskleidung, Trommel- und Walzenbelegung, Industrievulkanisation
Syntech Poliurea Top Coating: Zaščitna prevleka na osnovi alifatske poliuretanske smole

Syntech Poliurea Top Coating: Zaščitna prevleka na osnovi alifatske poliuretanske smole

Syntech Poliurea Top Coating A protective, pigmented, two-component formulation based on aliphatic polyurethane resins, ideal as a protective and aesthetic coating on waterproofing with SYNTECH POLIUREA SPRAY. Characterised by high levels of elasticity and elevated protection, even in aggressive atmospheres. Available on request in shades from the RAL colour range. Surface coating pigmented for colouring polyurethane claddings, and their protection from UV rays (which in the absence of the top coating would alter the colour over time). After suitable priming with SYNTECH POLYUREA PRIMER, it can also be applied as a simple coloured aliphatic protective coating. Polyurea support Vacuum and blow the surfaces to eliminate any dust that may have accumulated in the 24-48 hours following the installation of SYNTECH POLIUREA SPRAY Support in concrete, mortar, brick, tiles The support on which the polyurea system must be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. The humidity of the support must be <= 3%. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. In case of presence (even suspected) of humidity deriving from capillary rising from the substrate, it is recommended to apply in advance the epoxy resin for "wet substrates" Syntech Pavidamp. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. It is recommended to use Primer from the SYNTECH POLIUREA PRIMER range. On particularly absorbent substrates, to avoid the formation of craters / blowholes on the surface of the freshly sprayed product, it is recommended to use primers from the SYNTECH POLIUREA PRIMER range, always contacting the Azichem technical staff for clarification on the most suitable type to use. Apply several layers of primer until the porosity is saturated and providing a light dusting with clean and dry quartz sand (0.4-0.7 mm). Never dust off the primer. Provide suitable elastic sealing systems to cover joints, fittings, cracks or fissures subject to significant movements. Pour component B with component A into a single container, taking care to remove all the material from the packaging. Mix thoroughly with a mixer at low revs, until a lump-free mixture is obtained. Apply with a roller or brush on the surfaces of SYNTECH POLYUREA SPRAY, within 24-48 hours of spreading the latter. A thorough sanding of the supports is recommended for any repairs and/or finishes. From 0.15 to 0.25 kg of SYNTYECH POLIUREA TOP COATING for each square metre of surface to be covered. Can 6.7 kg [A] - Can 3.3 kg [B] - Kit: 1 Can 6.7 kg [A] + 1 Can 3.3 kg [B]
Syntech Poliurea Spray-Soft: Dvokomponentni epoksidni premaz za poliureu, primeren za vse površine

Syntech Poliurea Spray-Soft: Dvokomponentni epoksidni premaz za poliureu, primeren za vse površine

Syntech Polyurea Spray-Soft SYNTECH POLYUREA PRIMER is a two-component formulation based on epoxy resin in combination with cycloaliphatic amine hardeners. It is characterised by high values of penetration ability, and reinforcement, with particular reference to concrete surfaces, and is also indicated on most media and surfaces found in the building industry. Specific for the preparation of surfaces prior to coating them with SYNTECH POLYUREA SPRAY. Preparation of media and building surfaces (concrete, ceramics, wood, glass, cement, etc.), prior to coating them with SYNTECH POLYUREA SPRAY. The surfaces of application will be conveniently seasoned, prepared, adequately strong and absorbent; exempt from phenomena of rising damp surface, dust, grease, soiling, crumbling and non-adhering parts, hydro-repellent coatings or detected humidity. For more degraded floorings, in addition, preliminary shot peening or milling of the surfaces may be required. Pour component B with component A into a single container, taking care to remove all the material from the packaging. Mix thoroughly with a mixer at a low number of revolutions, or with a suitable worksite tool, for about 2 minutes, until a smooth lump-free mixture is obtained. Lay a homogeneous layer of product on the previously prepared surfaces to be treated, preferably by roller or brush. Thanks to the particular chemical structure of the amine curing used, SYNTECH POLYUREA PRIMER is responsive and effective even in cold weather. Barrel 225 kg [A] - Barrel 200 kg [B] - Kit: 1 Barrel 225 kg [A] + 1 Barrel 200 kg [B]
Prodaja PPF filma

Prodaja PPF filma

Développé et amélioré au fil des années, le PPF est à ce jour un traitement haut de gamme à l’aspect transparent préservant l’aspect esthétique du véhicule. Applicable aussi bien sur une voiture qu’une moto, il recouvre l’intégralité des surfaces de la carrosserie ou seulement des zones définies selon les besoins du propriétaire : phares, pare-chocs, etc. Pour un entretien complet de votre véhicule à Fréjus, découvrez les autres techniques de protection de carrosserie, comme le traitement céramique ou le nettoyage en profondeur intérieur et extérieur de votre voiture.
Hladno Lepilo ELASTOSAL H20

Hladno Lepilo ELASTOSAL H20

CKW-freier, lösemittelhaltiger 2K-Kontaktklebstoff auf CR-Basis für Gummi, Metall, Gewebe, Neopren z.B. als Kaltklebstoff für Fördergurte, Verschleißschutzauskleidung, Trommel- / Walzenbelegung