Izdelki za karbolit gero uk (23)

CARBOPAL, Pulverkohle zur Behandlung von Flüssigkeiten, ist in den folgenden Qualitäten erhältlich: • Carbopal MB 4 • Carbopal MB 4N • Carbopal MB 4S • Carbopal AP • Carbopal Gn-A II • Carbopal Gn-P

Osmocem SCK Fiber-reinforced monocomponent cement mortar, based on hydraulic binders, superprogoline fillers, selected fine aggregates and crystallizing reagent agents, which favor the penetration of the compound into the support. Ideal for low-thickness protective coatings (4 to 10 mm), with high counterweight adhesion. The specific formulation makes this product ideal for coatings in aggressive environments in contact with chlorides and sulphates (sewage systems). Packaging: 25 kg bag UM: €/kg

Molecular formulaC3H6O2 Molecular weight74.1 CAS number646-06-0 EC number211-463-5 IUPAC name1,3-Dioxolane EC name1,3-Dioxolane Molecular Formula:C3H6O2 Molecular weight:74.1 CAS Number:646-06-0 EC number:211-463-5 IUPAC name:1,3-Dioxolane EC name:1,3-Dioxolane

CARACTERISTIQUES DE LA BOUTEILLE Nature du gaz transporté : G.P.L Pression service(PS) : 20 Bar Diamètre extérieur (d) : 311+3-1 mm Epaisseur min paroi des bouteilles(e) : 2.5 mm Epaisseur min virole(e) : 2.6 mm Pression d’épreuve (PH) : 30 Bar Capacité de la bouteille : 84 Litres Hauteur des fonds elliptiques soudés sons pied ni collerette (h) : 1230+5-5 mm Hauteur de la bouteille (totale) sans valve (H) : 1337+10-5 mm Fond elliptique : relation entre axes de l’ellipse intérieure : 2 Dilatation min du volume de la bouteille avant rupture : 20%

El PCC se diferencia del GCC (Carbonato cálcico natural) por poder: -Disponer de partículas de menor tamaño y más uniformes. -Presentar distribuciones granulométricas más estrechas y estables. -Ejercer menor abrasión -Presentar superficies específicas superiores. -Asegurar purezas químicas más elevadas. Le PCC se différencie du GCC (Carbonates de Calcium Naturels) en ce qu’il permet de : -Disposer de particules plus petites et plus uniformes. -Présenter des distributions granulométriques plus étroites et plus stables. -Exercer moins d’abrasion. -Présenter des surfaces spécifiques supérieures. -Assurer des puretés chimiques plus élevées. The PCC can be distinguished from the GCC (Ground Calcium Carbonates) for: -The possibility to achieve smaller and more uniform particle sizes -More stable and narrower granulometric distribution -Lower abrasivity -Higher specific surface -Highest chemical purity.

C9 hydrogenated hydrocarbon resin is water-white thermoplastic resin obtained from polymerizing of aromatic and hydrogenation. Mainly used as tackifier for hot melt adhesive and hot melt pressure sensitive adhesive.

92-96% CaCO3 min. 50% CaO

Crotamiton is an active pharmaceutical ingredient produced under cGMP. * only European manufacturer * competitive process * up-to-date documentation * starting materials sourced from EU (no dependence on China) Crotamitone is an antipruriginosum used to treat burial mites (scabies). It works against the mites themselves, but also against the itching. CAS:483-63-6 Product Information:API Indication:Scabicidal and antipuritic Dosage:liquid Route of Synthesis:Synthetic Loss of Exclusivity:expired in EU, US

CBD ISOLAT 98%, 1 kg Isolat de CBD Premium 99,0% + cannabidiol pur de la plante de chanvre. CBD naturel sous forme de cristaux. Il s'agit d'un isolat de CBD certifié de haute qualité. Certifié en laboratoire Sans THC 0,00% Extraction de CO2 À partir de 1kg 2000,00 €, à partir de 5kg 1600,00 €, à partir de 10kg 1300,00 €

We are manufacturer and seller of NATURAL ZEOLITE (Clinoptilolite) Packing : in 25 Kg PP Bags on Pallets or 1 ton Big Bag Sizes : < 100 micron , 0-1 mm, 0,7-1,2 mm and other size : on request. Delivery Capacity : 6000 tons per Month Country of origin : Turkey Application : AGRICULTURE, GULF COURCE , WATER TREATMENT FILTER, OIL DRILLING

Silicium/L-Carnosine 1- Apport de silicium 2- Apport de carnosine 3- Apport de sélénium CarnoSilicium® réunit pour la première fois ces 3 ingrédients. L’organisme, à travers les années, s’altère continuellement par le phénomène d’oxydation (causé par des radicaux libres) et par le phénomène de glycation (réaction des molécules de sucres avec les protéines), aussi nommé « réaction de Maillard ». Cette réaction conduit à une dégradation des protéines, entrainant la perte d’élasticité et le durcissement des tissus. CarnoSilicium® s’adresse aux personnes ayant besoin d’un apport complémentaire pour contribuer à protéger les cellules contre le stress oxydatif grâce au sélénium, notamment les seniors et personnes exposées au vieillissement des tissus.

Cortec Boiler Dragon™ is a cutting-edge vapor corrosion inhibitor (VCI) safeguarding boilers, steam systems, and metal equipment from rust and corrosion. Developed by Cortec Corporation, this innovative solution leverages vapor phase corrosion inhibitors for comprehensive protection.Its unique VCI compounds emit corrosion-inhibiting vapours, forming a molecular barrier on metal surfaces against moisture, oxygen, and corrosive elements.Unlike traditional methods, the Boiler Dragon's vapor-phase action protects hard-to-reach areas and internal components.  Easy to use and versatile, the Boiler Dragon is simply mixed with water and applied.It's suitable for various metal machinery, from large industrial boilers to small steam generators.The solution forms a stable, ready-to-use mixture for spraying, fogging, or immersion, creating a protective vapor cloud.This ensures comprehensive coverage, safeguarding both external and internal components.

Reiner CBD Kristall enthält 99,8 % CBD. Im Speziallabor getestet. Unsere Kristalle entstehen durch Extraktion von EU-zertifizierten, biologisch angebauten Hanfpflanzen. Nicht psychoaktiv (nicht berauschend). Gewicht: 1 g

KENDİNİZ VE SEVDİKLERİNİZ İÇİN • Antiviral, Antibakteriyel, • Antifungal ve yüksek antioksidant etkisiyle, • Vücut direncini artırmaya, • Yaşlanmayı geciktirmeye, • Hormonları dengelemeye yardımcı olduğu gibi içerisinde bulunan çinko, magnezyum ve kalsiyum mineralleri ile mineral eksikliğini gidermeye YARDIMCI OLUR.

What is calcium hypochlorite? Calcium hypochlorite is a white solid that contains 65% available chlorine and dissolves easily in water. It is very stable and can be stored for an extended period of time. It is a corrosive material with a strong odor. Other names is Hypochlorous acid calcium salt, bleaching powder, calcium oxychloride and chloride of lime. What is calcium hypochlorite used for? Its and Sodium are used primarily as oxidizing and bleaching agents or disinfectants. They are components of commercial bleaches, cleaning solutions, and disinfectants for drinking water and waste water purification systems and swimming pools. It is an inorganic compound added in granular or tablet form added to water to kill germs that can make people sick. When used correctly, this compound destroys germs that can cause numerous health problems.

Pour l’agglomération du minerai de fer, ces castines sont constituées de calcaire à plus de 97% de carbonate de calcium. Elles servent également de composant dans les engrais. Contactez-nous pour des informations complémentaires

Fluid Col Multi-purpose additive powder, to add to a suitable mixture of binders and aggregates, for the on-site production of mortars, grouts and concretes that are self-levelling, rheoplastic, controlled shrinkage or moderately expansionary, high mechanical strength, chemical and waterproofing. The physical-chemical action of Fluid Col is an interaction of positive contributions and modifications: drastic reduction of the A/C ratio, shrinkage-resistant action, superpozzolanic action and reaction of ultrafine fillers (MICROSIL 90), which transforms unstable, soluble, readily reactive calcium hydroxides into stable, insoluble, chemically and mechanically resistant hydrous calcium silicates. Preparation of mortars, grouts, rheofluid concretes, shrinkage-compensated or moderately expansionary, high mechanical, watertightness and chemical stability performance, for structural slubs, anchoring machines, road joints, etc. Add the product in a concrete mixer, mixer truck or mixer, together with the remaining anhydrous components of the mixture: cement and aggregates, any polypropylene and/or steel fibres, etc. The indicative dosage, depending on the type of conglomerate to be packaged and its purposes, varies between 12% and 15% of the weight of the cement. After a first mixing, add the mix water and mix thoroughly, until you obtain a homogeneous whole and free of lumps. The cement dosage must not be less than 350 kg/m³. Fluid Col is perfectly compatible with the addition of fibre d steel and/or polypropylene fibres READYMESH, for the preparation of conglomerates composite s, fibre reinforced. Add 10 - 15% of Fluid Col to the weight of the cement present in the mixture. Bag 25 kg - Pallet: 50 x (Bag 25 kg)

Grout CR Composite , castable, anti-washout, controlled shrinkage cement mortar, superfluid consistency, based on high-resistance cements, superpozzolanic fillers (MICROSIL 90), polymeric modifiers, shrinkage resistant agents, specific additives, calcium silicate mineral fibres, selected silica aggregates. - Based on of thickened silica fume - three-dimensionally reinforced fibre with mineral and synthetic fibres - Provides high adherence and adhesion - dimensionally stable (shrinkage-compensated) - Provides high stability-physical chemical and resistance to chlorides and sulphates - suitable for underwater castings: it is anti-washout - high strength in terms of hydrostatic positive and negative thrust. Repair and protective coatings of hydraulic structures, marine and underwater structures, and articles in critical situations: harsh chemical-physical, leaching water, marine atmosphere, etc. Filling of formwork for the containment of cast immersed in sea water. In case of underwater application, the installation operations must be carried out within 8-10 hours of cleaning and "fouling" (accumulation and deposits of organic and inorganic particles on product surfaces) removal. An adequate roughening of the surfaces by scarifying, sandblasting etc. is always necessary in order to obtain the maximum adhesion values to the substrate. The optimal values are obtained with high pressure hydro-scarification. Bare the irons undergoing disruptive oxidation or deeply oxidized, removing the rust of the exposed irons (by sandblasting or abrasive brushes). Pour 2/3 of total mixture water in the cement mixer, gradually add the product and the remaining water, until a homogeneous mixture of the required consistency is obtained. For sizable filling thicknesses, greater than 60 mm, Ghiaietto 6.10 (inert washed is selected with a particle size of from 6-10 mm) can be added in a percentage ranging from 20% to 40 %, on the basis of practical requirements. In some particularly demanding cases in terms of the resistance to the "dry-wet" cycle (for example, for the action of the tides) or for chemical attacks particularly strong, it would be advisable to add, in addition to the gravel, even thickened silica fume(MICROSIL 90), and in a variable amount depending on the thickness and construction-related need, to further improve the waterproofing and the mechanical strength of the product. In these cases, please contact our Technical Service. In the case of casts in water, make sure of perfect product hardening before removal of the formwork. Approximately 20,50 kg/m² of Grout CR for every centimetre of thickness to be implemented (approximately 2050 kg per cubic metre). Packaging: 25 kg bag UM: €/kg

Grout 6 HP SFR Grout 6 HP SFR is a fibre-reinforced high-performance castable mortar, equipped with mechanical compressive and flexotraction resistance far superior to normal structural mortars. It is used for repairs, replenishments, strengthening concrete reinforcement and special works in FRC. The mix of special metal fibres (Readymesh MM-150) and synthetic fibres (Readymesh PM-060) is able to drastically reduce or even eliminate plastic-hygrometric shrinkage and the development of exceptional characteristics of ductility, fracture energy, resistance to shock and dynamic stress. With very low water-binder ratios, Grout 6 HP SFR makes it possible to achieve compacting and hyperfluid rheologies that favour the movement of the mortar and the perfect filling of reinforced sprays, even with narrow spaces between the bars. The microsilica with pozzolanic activity increases the cohesion of the mixture with typical anti-segregating and anti-run-off effect. The particular fineness of the hydraulic binders contained in the formula promotes adherence to the substrate and has an effect of enlarging the fibrous components. The fibre mix offers strong ductility, toughness and flexotraction resistance to the castings performed with Grout 6 HP SFR. With regard to the ANTICORROSIVE and PROTECTIVE FUNCTION ON THE REINFORCEMENT BARS, the main features of Grout 6 HP SFR are: • the mix of high-strength superfine binders, combined with very fine silicas with pozzolanic activities, to render the mortars intrinsically impermeable to water at the end of the hardening process; • The strongly alkaline pH (> 12) protects the reinforcement bars from triggering corrosion; • The negligible breathability of the carbon dioxide ensures hardened mortars with extremely prevalent anti-carbonation characteristics. Overall, these anticorrosive specificities render the classic treatment of reinforcement bar passivation, preparatory to the pouring of castable mortar UNNECESSARY, provided that not too much time passes between the white metal cleaning operations and the castings of pourable mortar, at the risk of new oxidative processes being triggered. Thus, only in the event that long exposure times are foreseen between the bar-cleaning operations and the pouring of castable mortar is it advisable to treat with passivating slurry (Repar Monosteel or Repar Steel), applied by brush and only on the reinforcing bars. On-site castings or pumping carried out for any kind of structural replenishment of reinforced concrete, seismic reinforcement and adjustment, increases in cross-sectional resistance of concrete structures and masonry, anchorages of large-scale machinery (especially in the presence of significant dynamic stresses), anchoring of port bollards, deep-drawing and reinforcement works, restoration of highly-stressed industrial flooring both from a static and dynamic perspective, restoration of degraded foundations on bridges and viaducts especially whereby necessitating rapid reopening to vehicle traffic, construction of structures designed with HPC (High Performance Concrete) needs. Application surfaces must be clean, free of dust, contamination, crumbling, inconsistencies, etc., and adequately saturated-surface-dry with water. An adequate roughening of the surfaces by scarifying, sandblasting etc. is always necessary in order to obtain the maximum adhesion values to the substrate. The optimal values are obtained with high pressure hydro-scarification. Bare the irons undergoing disruptive oxidation or deeply oxidized, removing the rust of the exposed irons (by sandblasting or abrasive brushes). Mix the entire content of a bag of Grout 6 HP SFR with effective vertical-axis mixers for at least 6 minutes, initially introducing a slightly reduced amount of water (9% = 2.25 litres/25 kilograms bag) compared to the required total water permitted (10%–12% = 2.5litres — 3.0 litres/25 kilogram bag) whilst mixing for at least 4 minutes. After this mixing time, evaluate the consistency of the mixture and, if necessary, gradually add in the last of the water until achieving the desired workability, without exceeding the limit of 12% (3.0 litres/25-kilogram bag), mixing at high RPM for at least another two minutes. For thick casting sections, it is advisable to add Ghiaietto 6.10 (consult the relevant technical data sheet or ask for more information on the appropriate dosage of Ghiaietto 6.10 from our technical service). Given the self-levelling properties of the product and its self-compacting capacity, paying due attention to the vibration phase is recommended. Excessive zeal in the vibration operation can worsen the aesthetic rendering of the end result. Do not use in the absence of suitable lateral containment. Ensure exposed surfaces are protected and wet-cured. Adopt casting procedures to ensure the absence of voids and discontinuities. Only pour the mortar from one part of the casting perimeter to avoid air pockets. Packaging: 25 kg bag UM: €/kg

Grout 2 HP Grout 2 HP is a pourable, fiber-reinforced mortar, used for structural restoration operations, anchoring of steel bars and strands, reinforced micropiles, tie rods, and riveting. The formulation contains very fine high-strength cements, micro-silicas with pozzolanic activity, aggregates in a rational granulometric curve (0.1 ÷ 1.8 mm), and special antisegregative additives. The product is mixed with 11% - 12% of water, requiring vigorous and prolonged mechanical mixing. The special formulation of Grout 2 HP provides the castings with mechanical strength, fracture energy, exceptional durability, and very high chemical-physical resistance. Grout 2 HP has a workability time of about 60-90 minutes, after which the setting process is triggered, followed by progressive hardening. The plastic and hygrometric shrinkage is extremely low thanks to the presence of Readymesh PM-060 multifilament synthetic fibers, which provide volumetric stability. The performances that make Grout 2 HP unique are: • very high compressive mechanical strengths (> 90 MPa at 28 days), • very high mechanical resistance to bending-traction (> 12 MPa after 28 days), • excellent durability and resistance to chemical attacks. Grout 2 HP is used for structural restoration operations, anchoring of steel bars and strands, reinforced micropiles, tie rods, and riveting. It is particularly suitable for operations where high mechanical performance is required after short curing (compressive strength at 3 days > 60 MPa) and in operations carried out in severe exposure environments (XC - XS - XF), characterized by aggression from sulphates, chlorides, and nitrates. The material can also be used for repairs in anchoring areas subject to high stresses. The application surfaces must be clean, free of dirt, crumbly and incoherent parts, dust, etc., and suitably saturated with water until reaching the condition of "saturated with dry surface". Adequate roughening of the surfaces by scarifying, sandblasting, etc. is always necessary to obtain the maximum adhesion values to the substrate. The optimal values are obtained with high pressure hydro-scarification. Bare the irons undergoing disruptive oxidation or deeply oxidized, removing the rust of the exposed irons (by sandblasting or abrasive brushes). It is strongly recommended, for optimal performance of site operations, to use a vertical axis mixer with planetary movement or a double horizontal helicoid. The powder is mixed with drinking water to the extent of 11% - 12%, referring to the total weight of the mortar (about 2.75 liters per 25 kg bag) until a homogeneous mixture is obtained. Mixing time: about 4 minutes with a high efficiency mixer. The anchoring can be filled with a single screw pump, for mortars. Pumping must be carried out at a controlled speed to ensure a low working pressure. In case of restorations, the surface must be protected, after application, by polyethylene sheets or anti-evaporation treatments. Packaging: 25 kg bag Unit of Measure: €/kg

C5 hydrogenated hydrocarbon resin is water-white thermoplastic resin obtained from cracking C5 by hydrogenation. Mainly used in non-woven fabrics field, HMA,PSA.

CBD ISOLAT 98%, 1 kg Il CBD premium isola il 99,0% + cannabidiolo puro dalla pianta di canapa. CBD naturale sotto forma di cristalli. È un isolato di CBD certificato di alta qualità. Certificato di laboratorio Senza THC 0,00% Estrazione di CO2 Da 1 kg 2.000,00 €, Da 5 kg 1.600,00 €, Da 10 kg 1.300,00 €

Propofol belongs to the group of phenol derivatives. The active substance is a short-acting anesthetic. It is used for the initiation and maintenance of intravenous anesthesia. Name:Propofol CAS Number:2078-54-8 Indication:Anesthesia, sedation