Izdelki za oprema za vakuum (5)

Tip Enhanced Raman Scattering (TERS, nanoRaman) is the technique for enhancement of weak Raman signals and for superresolution Raman imaging with spatial resolution less than 10 nm. As a result of comprehensive research performed together with NTMDT SI customers and partners, we are now able to offer to AFMRaman customers mass produced reproducible TERS probes. TERS imaging requires prolonged tipsample contact at each scanning point but Contact AFM is destructive for both the tip and the sample. Thereby, HD mode is a superior technique for cantilevertype TERS since it noticably increases the tip lifetime and makes possible TERS imaging of soft, loose and fragile samples. Vacuum measurements in amplitude modulation (AM) mode requires unacceptably low scanning speeds because of extremely high Qfactor of AFM probes. Being a nonresonant mode, HD mode allows at least 10 times faster imaging speed.

Vacuum truck MV is intended for the collection of liquid waste, technical water and their further transportation to utilization spot. By means of the pump vacuum is created inside the tank and the liquid, pumped through the hose, is supplied inside the tank. Tank discharge is carried out by gravity drainage or with the help of the pump, boosting air inside the tank. Unit is equipped with: Tank with support, Pump unit, Power take-off unit for pump drive, Piping, drain valve and other extra equipment. Chassis:GAZ, ZIL, KAMAZ and other Dimensions: length * width * height:7 000 * 2 200 * 2 600 mm Tank capacity:4 m3 Maximum vacuum inside the tank:0,08 MPa Pump output:240 m3/ч Suction depth:4 m

This magnetic system is specially designed for non-destructive testing of pumped vacuum devices, that required the creation of a uniform magnetic field not only in the center of the operating bore, but in the toroidal region of large size. The system is assembled on the basis of NdFeB permanent magnets. Field direction:axial Field uniformity in a specified toroidal area:up to ±2% Magnetic flux density (for existing modifications):from 0.1 to 0.4 T Bore diameter:120 mm and more

The truly powerful MAX Ultimate VII. Equipped with a unique proprietary fan. This is amazing! Imagine that you have just finished doing a nail correction for a client, and the table is clean. No more masks, sawdust on a wet napkin and other tricks. You just work clean. Do you like the feeling? Then the choice is obvious. Order your MAX Ultimate VII right now! Super fan Ultimate VII. Not just powerful, but special. Designed specifically for a manicure nail dust collector. The number of impeller blades is 9. A record among analogues! The blades become thinner towards the impeller edge. The effect is that the fan sucks in the dust-air mixture better. The powerful electric motor is located outside the fan housing. The effect: a more powerful fan can be inserted in a housing of the same size. Special design of the fan housing. This made it possible to remove the gap between the fan walls and the impeller, which any conventional fan has. Certified product. Fan speed:0 - 2500 rpm Estimated performance:401 m3/hour Estimated fan life:50 000 hours LxWxH:33х32х17,5 cm Weight without pillow:1,8 kg Weight with pillow:2,1 kg Voltage:220 V Type of plug:Euro

The truly powerful MAX Ultimate VII. Equipped with a unique proprietary fan. This is amazing! Imagine that you have just finished doing a nail correction for a client, and the table is clean. No more masks, sawdust on a wet napkin and other tricks. You just work clean. Do you like the feeling? Then the choice is obvious. Order your MAX Ultimate VII right now! Super fan Ultimate VII. Not just powerful, but special. Designed specifically for a manicure nail dust collector. The number of impeller blades is 9. A record among analogues! The blades become thinner towards the impeller edge. The effect is that the fan sucks in the dust-air mixture better. The powerful electric motor is located outside the fan housing. The effect: a more powerful fan can be inserted in a housing of the same size. Special design of the fan housing. This made it possible to remove the gap between the fan walls and the impeller, which any conventional fan has. Certified product. Fan speed:0 - 2500 rpm Estimated performance:401 m3/hour Estimated fan life:50 000 hours LxWxH:33х32х17,5 cm Weight without pillow:1,8 kg Weight with pillow:2,1 kg Voltage:220 V Type of plug:Euro