Izdelki za poliuretan 80 (8)

Syntech Poliurea Top Coating A protective, pigmented, two-component formulation based on aliphatic polyurethane resins, ideal as a protective and aesthetic coating on waterproofing with SYNTECH POLIUREA SPRAY. Characterised by high levels of elasticity and elevated protection, even in aggressive atmospheres. Available on request in shades from the RAL colour range. Surface coating pigmented for colouring polyurethane claddings, and their protection from UV rays (which in the absence of the top coating would alter the colour over time). After suitable priming with SYNTECH POLYUREA PRIMER, it can also be applied as a simple coloured aliphatic protective coating. Polyurea support Vacuum and blow the surfaces to eliminate any dust that may have accumulated in the 24-48 hours following the installation of SYNTECH POLIUREA SPRAY Support in concrete, mortar, brick, tiles The support on which the polyurea system must be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. The humidity of the support must be <= 3%. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. In case of presence (even suspected) of humidity deriving from capillary rising from the substrate, it is recommended to apply in advance the epoxy resin for "wet substrates" Syntech Pavidamp. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. It is recommended to use Primer from the SYNTECH POLIUREA PRIMER range. On particularly absorbent substrates, to avoid the formation of craters / blowholes on the surface of the freshly sprayed product, it is recommended to use primers from the SYNTECH POLIUREA PRIMER range, always contacting the Azichem technical staff for clarification on the most suitable type to use. Apply several layers of primer until the porosity is saturated and providing a light dusting with clean and dry quartz sand (0.4-0.7 mm). Never dust off the primer. Provide suitable elastic sealing systems to cover joints, fittings, cracks or fissures subject to significant movements. Pour component B with component A into a single container, taking care to remove all the material from the packaging. Mix thoroughly with a mixer at low revs, until a lump-free mixture is obtained. Apply with a roller or brush on the surfaces of SYNTECH POLYUREA SPRAY, within 24-48 hours of spreading the latter. A thorough sanding of the supports is recommended for any repairs and/or finishes. From 0.15 to 0.25 kg of SYNTYECH POLIUREA TOP COATING for each square metre of surface to be covered. Can 6.7 kg [A] - Can 3.3 kg [B] - Kit: 1 Can 6.7 kg [A] + 1 Can 3.3 kg [B]

Anstrichverträglicher Einkomponenten-Dichtstoff auf Basis Acryldispersion zur Abdichtung von Anschluss- und Bauteilfugen. Schnellregenfest. 2H Acryl 250 ist ein hochwertiger schnellregenfester plastischer Einkomponenten-Dichtstoff auf Basis Acryldispersion. Durch Verdunstung der Wasseranteile härtet 2H Acryl 250 zu einem alterungs-, witterungs- und UV-beständigen Dichtstoff aus. Kartuschen á 310 ml Folienbeutel á 310 ml Folienbeutel á 600 ml

Chlorwasserstoff zur Synthese von Chemischen Produkten und Pharmaprodukten, Anwendung in der Pharmaindustrie, Oberflächenbehandlung, Ätzen von Metallen.

40% formaldehyde solution in water, which is a chemical compound highly used in various industries. It appears as a clear, colorless liquid with a pungent, pungent odor. Formaldehyde is widely used in the manufacture of wood products, as an adhesive and preservative, as well as in the production of resins and plastics. It is also used in the textile, paper and personal care products industries, as a preservative. Despite its industrial usefulness, formaldehyde can be irritating to the skin and respiratory tract, so its use is regulated and controlled in many regions to ensure the safety and protection of workers and consumers. CONTAINER:5kg, 25kg and 200kg IBC

Bond Plus Adhesive latex based on elastomeric styrene-butadiene rubber and alkaline silicate in aqueous dispersion, flexibilising, reactive, for adhesive grout and to improve adhesion, the behaviour and performance of mortars and plasters. Production of adhesive, deformable, high-protective and waterproofing performance mortars and plasters for civil, hydraulic, industrial works, in urban, marine and mountain atmospheres. Preparation of hydrating solutions to improve the adhesion and performance of premixed mortars and plasters; preparation of adhesive grouts for non-structural construction joints. Anti-dust treatments, reinforcing concrete surfaces. Shake Bond Plus thoroughly in the tank, and dilute it with water as required. Add the prepared solution to the cement (or lime) and aggregates mixture, in the most suitable dosages for this application, as specified below. It is always essential to carry out preliminary tests for an accurate definition of the mixtures to use, and to check the suitability of the product on the basis of the specific requirements. Refer to the table shown in the product datasheet. Packaging: 25 kg can UM: €/kg

2H Acryl 150 mit Quarzsand ist ein elastoplastischer Dichtstoff auf Acryldispersionsbasis für innen und außen. Einkomponentiger Acrylatdichtstoff für den Innen- und Außenbereich mit einer max. Bewegungsaufnahme von 10%. Putzähnliche Oberfläche zum Verschließen von Rissen in Putz und Mauerwerksflächen innen und außen. Verpackung in 310ml Kartusche.

EG 91 Epoxy-polyurethane two-component elastoplastic and thixotropic sealant, for joints subject to traffic, where Shore A Hardness Scale = 65. The elongation-at-break is 70%. To be applied with a trowel or extruded into the suitably-taped sections of the joint (to protect adjacent surfaces). Resistant to contact with hydrocarbons (gasoline and diesel fuel). Horizontal sealing of joints in industrial flooring, even in the presence of chemical attacks and stresses from average-heavy traffic. Vertical sealing of joints in concrete works and products. The application and containment surfaces (joint walls) should be clean, dry, conveniently prepared and adequately resistant: free from dust, grease, soiling, crumbling and/or non-adhering parts and dry. The application surfaces must also be preliminarily treated with Protech Flex Primer. Add component B to component A taking care to pick up all the material contained in the packs, mix thoroughly with a mixer at a low number of revolutions, until a perfectly homogeneous mix is obtained; add the required load amount (component C) continue to mix until a perfectly homogeneous mixture is obtained, indicated by the uniform colour of the mixture. Apply the product mixed by trowelling or with extrusion guns. Do not apply with temperatures below + 5°C or higher than + 35°C and in the presence of surface stagnant water. Approximately 1.25 kg of EG 91 per cubic decimetre of joint volume to be sealed (1250 kg per cubic metre). Packaging: Kit of 5+2.5 kg UM: €/kg

Methyl red is an organic compound that belongs to the family of azo dyes. It appears as a deep red powder, soluble in water and slightly soluble in ethanol. It is widely used as a pH indicator in acidic and basic solutions, as it changes from red in acid to yellow in alkaline. In addition to its use as an indicator, methyl red is used in the coloring of textiles, inks, cosmetics and as a dye in the food industry. However, its use in food applications is regulated due to concerns about its safety and potential toxicity in large quantities. CONTAINER:5kg. 25kg. 200kg. IBC