Izdelki za sikantal epoksi (14)

Anstrichverträglicher Einkomponenten-Dichtstoff auf Basis Acryldispersion zur Abdichtung von Anschluss- und Bauteilfugen. Schnellregenfest. 2H Acryl 250 ist ein hochwertiger schnellregenfester plastischer Einkomponenten-Dichtstoff auf Basis Acryldispersion. Durch Verdunstung der Wasseranteile härtet 2H Acryl 250 zu einem alterungs-, witterungs- und UV-beständigen Dichtstoff aus. Kartuschen á 310 ml Folienbeutel á 310 ml Folienbeutel á 600 ml

EG 91 Epoxy-polyurethane two-component elastoplastic and thixotropic sealant, for joints subject to traffic, where Shore A Hardness Scale = 65. The elongation-at-break is 70%. To be applied with a trowel or extruded into the suitably-taped sections of the joint (to protect adjacent surfaces). Resistant to contact with hydrocarbons (gasoline and diesel fuel). Horizontal sealing of joints in industrial flooring, even in the presence of chemical attacks and stresses from average-heavy traffic. Vertical sealing of joints in concrete works and products. The application and containment surfaces (joint walls) should be clean, dry, conveniently prepared and adequately resistant: free from dust, grease, soiling, crumbling and/or non-adhering parts and dry. The application surfaces must also be preliminarily treated with Protech Flex Primer. Add component B to component A taking care to pick up all the material contained in the packs, mix thoroughly with a mixer at a low number of revolutions, until a perfectly homogeneous mix is obtained; add the required load amount (component C) continue to mix until a perfectly homogeneous mixture is obtained, indicated by the uniform colour of the mixture. Apply the product mixed by trowelling or with extrusion guns. Do not apply with temperatures below + 5°C or higher than + 35°C and in the presence of surface stagnant water. Approximately 1.25 kg of EG 91 per cubic decimetre of joint volume to be sealed (1250 kg per cubic metre). Packaging: Kit of 5+2.5 kg UM: €/kg

Acryl by Sarközy ist eine überstreichbare Dichtmasse auf Basis von Acryldispersion. Ab einer Kartusche erhältlich! Acryl by Sarközy wird erfolgreich eingesetzt bei Fassaden, im Fensterbau, den Oberkante-Sockeln und Türzargen. Das Verfugen von Anschlussfugen zwischen Beton und Mauerwerk oder Decke und Wand sind die klassischen Anwendungen dieser Dichtmasse. Acryl by Sarközy Dichtstoff ist nahezu geruchlos und nicht korrosiv. Es ist witterungsbeständig, regenfest und bildet nach dem Einbringen durch Verdunsten von Wasser eine plastisch-elastische Masse. Grundstoff: Acryldispersion Kartuschenfüllmengen: 310ml Standardfarben: Weiß und Transparent

Colle de contact transparente à base polyuréthane - spécial PVC doux Pour double encollage de matériaux divers, durs ou flexibles, comme la plupart des matières synthétiques (PVC souple, PVC, ABS, plexi, polycarbonate), bois, panneaux de revêtements décoratifs stratifiés, placage et collage sur champ, nez de marches et marches d’escalier, plinthes en PVC, cuir, liège, textile, métaux entre eux ou sur bois, pierre, béton, plâtre, métal et autres supports lisses et non poreux. Spécifiquement pour des applications dont la couche de colle ou le joint de colle reste visible : comme le collage sur verre ou plexi. Aussi idéal pour la réparation de bâches, toiles de tente et pour matériaux gonflables en PVC souple. Prête à l'emploi, transparente au séchage, pas de trace brune, utilisation aisée à la brosse et au peigne à colle, force d'adhérence progressive rapide, résistante à l'humidité à la chaleur et au froid (-10°C jusqu'à +70°C) Résiste aux acides légers et bases Sans...

ISONEM METALLIC SHINE FLOOR est une résine de sol autolissant à base de polyuréthane et de solvant. (bi composants)

Blaspistolen, Abblashähne, Sprühpistolen, Profi-Reinigungspistolen und spezielle Druckluft- und Flüssigkeitspistolen gehören ebenso zum RIEGLER Produktprogramm wie auch Handreifenfüllmesser, Schlauchklemmen und Schlauchschellen, Dichtmaterial und verschiedene Versorgungseinheiten. Mit den RIEGLER Industrieklebstoffen, Sprays und Sticks sind sie immer auf der sicheren Seite.

Xypex Concentrate is the most chemically active product within the Xypex Crystalline Waterproofing System.When mixed with water, this light grey powder is applied as a cementitious slurry coat to above-grade or below-grade concrete, either as a single coat or as the first of a two-coat application. It is also mixed in Dry-Pac form for sealing strips at construction joints, or for the repairing of cracks, faulty construction joints and honeycombs. Xypex prevents the penetration of water and other liquids from any direction by causing a catalytic reaction that produces a non-soluble crystalline formation within the pores and capillary tracts of concrete and cement-based materials.

Solvant diélectrique à évaporation rapide Tension de claquage de 76 000 V Sans résidu, sans chlore – Point éclair non mesurable – Evaporation ultra rapide Nettoyage des générateurs, moteurs électriques, transformateurs, disjoncteurs. Aéronautique – Aérospatial – Plasturgie. Réf:DIEL554 Ex:PARTIE 35000 Conditionnement:Bidon de 5 L – Carton de 4, Fût de 20 L

Nous fournissons tout type de ciment colle fabriqué selon la norme EN 12004 : du Cilement colle basique (C1) à ciment colle haute performance (C2TES2)

2H Acryl 150 mit Quarzsand ist ein elastoplastischer Dichtstoff auf Acryldispersionsbasis für innen und außen. Einkomponentiger Acrylatdichtstoff für den Innen- und Außenbereich mit einer max. Bewegungsaufnahme von 10%. Putzähnliche Oberfläche zum Verschließen von Rissen in Putz und Mauerwerksflächen innen und außen. Verpackung in 310ml Kartusche.

Syntech Poliurea Primer – Epoxy Metal Syntech Poliurea Primer – Epoxy Metal is a two-component primer based on epoxy resins free from solvents, used to promote adhesion, as a surface sealant for concrete, applied as a substrate for works with polyureas on metal surfaces and epoxy and polyurethane coatings. Adhesion promoter, surface sealant for concrete, to be applied as a substrate for works with polyureas on metal surfaces and epoxy and polyurethane coatings. The application must take place on a dry and degreased surface; the substrate must not have crumbly or detached parts and with a degree of humidity that must not exceed 5%. Preparation of the substrate may require some types of mechanical action: Smoothing, bush-hammering, shot peening, hydro-washing. Other mechanical actions that can make the support suitable. The individual components must be mixed carefully until a homogeneous mass is obtained. The material can be applied by roller, brush or spray by means of special airless machines, even in two coats. The temperature of the support must always be at least 3°C higher than the dew point temperature. Minimum application temperature +5°C, maximum temperature +35°C. Approximately 0,20 kg of Syntech Poliurea Primer – Epoxy Metal for every square metre of surface to be treated. Can 10 kg [A] - Can 5 kg [B] - Kit: 1 Can 10 kg [A] + 1 Can 5 kg [B]

Syntech Poliurea Top Coating A protective, pigmented, two-component formulation based on aliphatic polyurethane resins, ideal as a protective and aesthetic coating on waterproofing with SYNTECH POLIUREA SPRAY. Characterised by high levels of elasticity and elevated protection, even in aggressive atmospheres. Available on request in shades from the RAL colour range. Surface coating pigmented for colouring polyurethane claddings, and their protection from UV rays (which in the absence of the top coating would alter the colour over time). After suitable priming with SYNTECH POLYUREA PRIMER, it can also be applied as a simple coloured aliphatic protective coating. Polyurea support Vacuum and blow the surfaces to eliminate any dust that may have accumulated in the 24-48 hours following the installation of SYNTECH POLIUREA SPRAY Support in concrete, mortar, brick, tiles The support on which the polyurea system must be laid must be suitable for withstanding the stresses resulting from the intended use, such as static or dynamic loads, impacts, thermo-hygrometric dilations, vibrations, etc. As regards the characteristics of the substrate (maximum humidity, cohesion, strength class, flatness, etc.) and the preparation of the surface that will accommodate the resin system, we recommend the requirements set out in chapter 5 of the UNI 10966 standard ("RESIN SYSTEMS FOR SURFACES HORIZONTAL AND VERTICAL - INSTRUCTIONS FOR DESIGN AND APPLICATION "). In any case, carefully clean and degrease the surfaces, removing any kind of dirt, paint residues or incoherent parts. The humidity of the support must be <= 3%. Evaluate the most convenient type of mechanical preparation (shot peening, sandblasting, hydro-washing, etc.). The surfaces must also be free from discontinuity, and possibly leveled and regularized with products from the FLOOR line or the REPAR line. In case of presence (even suspected) of humidity deriving from capillary rising from the substrate, it is recommended to apply in advance the epoxy resin for "wet substrates" Syntech Pavidamp. Tiled floors, or floors covered with pre-existing resin, must be subjected to mechanical roughening carried out with shot blasting, milling, bush hammering, etc., until the total elimination of the waterproof crust and the opacification of the surfaces. Remove dust after abrasion. It is recommended to use Primer from the SYNTECH POLIUREA PRIMER range. On particularly absorbent substrates, to avoid the formation of craters / blowholes on the surface of the freshly sprayed product, it is recommended to use primers from the SYNTECH POLIUREA PRIMER range, always contacting the Azichem technical staff for clarification on the most suitable type to use. Apply several layers of primer until the porosity is saturated and providing a light dusting with clean and dry quartz sand (0.4-0.7 mm). Never dust off the primer. Provide suitable elastic sealing systems to cover joints, fittings, cracks or fissures subject to significant movements. Pour component B with component A into a single container, taking care to remove all the material from the packaging. Mix thoroughly with a mixer at low revs, until a lump-free mixture is obtained. Apply with a roller or brush on the surfaces of SYNTECH POLYUREA SPRAY, within 24-48 hours of spreading the latter. A thorough sanding of the supports is recommended for any repairs and/or finishes. From 0.15 to 0.25 kg of SYNTYECH POLIUREA TOP COATING for each square metre of surface to be covered. Can 6.7 kg [A] - Can 3.3 kg [B] - Kit: 1 Can 6.7 kg [A] + 1 Can 3.3 kg [B]

Syntech HAG Acryl Syntech HAG Acryl is a four-component resin that reacts to form an elastic and durable gel. The properties of Syntech HAG Acryl are: • Good general chemical resistance. • Does not contain acrylamide, methacrylamide, formaldehyde or solvents. • Not inflammable. • Excellent adhesion on mineral building materials such as concrete, cement and bricks. • The reaction speed can be adjusted from a few seconds to several minutes. • When the injected cracks dry out due to temperature or groundwater level fluctuations the gel does not crack easily. • The hardened gel has excellent durability in wet-dry cycles. Syntech HAG Acryl components are supplied ready to use. Create 2 mixes in separate plastic buckets. Prepare only the quantity to be used each time. Solution 1: Syntech HAG Acryl component A (25 kg resin) mixed with Syntech HAG Acryl component B (2.5 kg catalyst). Solution 2: Syntech HAG Acryl component C (2 packs of 0.625 kg) mixed with clean tap water. Attention: The amount of water must be equal in volume to solution 1. When mixing resin, always use a wooden or stainless steel spatula. The reaction time depends on the temperature of the material, the structure of the building and the possible amount of water present. Higher temperature will speed up the reaction time and lower temperature will slow it down. It is advisable to carry out an on-site test, before injection, to observe and define the reaction time. To change the reaction time, only adjust the amount of Syntech HAG Acryl component C. The amount of the other components remains the same. Use a two-component stainless steel pump (manual, electric or pneumatic). Check that the pump and equipment are clean and that there is no residue from previous injection work. The two mixtures are fed into the pump separately, but are mixed homogeneously at a volumetric ratio of 1:1 in the pump's mixing head, before being injected through the pump nozzle. Check the quality of the concrete, as injection involves pressure. Sealing and waterproofing of cracks and cavities in walls, floors, concrete constructions, underground structures, etc. It can be used in constructions that are not permanently in contact with water (fluctuating groundwater level). Injection of very fine cracks. Determine the type and size of packers based on your pump and injection type. If reinforcing steel is present, try to locate it and plan the drilling pattern so that the reinforcement is not drilled. Drill holes at an angle of approximately 45° or less and in the direction of the crack. Make sure the hole goes through the crack. The distance of the drilled holes depends on the width of the crack. Place the packer in the hole. Prepare the pump to start the injection. The injection pressure varies depending on the structure and size of the crack. Start the injection at the lowest point of the crack. Continue injecting until resin flows out of adjacent packer(s). This is necessary to achieve uniform distribution of the material. Stop pumping, unplug and move on to the next packer. Continue the procedure until the crack is completely filled. After the material has cured, the packers can be removed. Holes drilled can be covered with Repar Tix Speedy HP quick-setting mortar. Clean and rinse the pump equipment with water whenever there is a stoppage longer than 15 minutes and, after completing the injection, rinse with a sufficient amount of water. Make sure the pump is clean and stop only when clean water comes out of the pump. The consumption of the product depends on the size of the empty volume to be filled. Can 25 kg [A] - Plastic can 2.5 kg [B] - Canister 0.625 kg [C] - Canister 0.625 kg [D] - Kit: 1 Can 25 kg [A] + 1 Plastic can 2.5 kg [B] + 1 Canister 0.625 kg [C] + 1 Canister 0.625 kg [D]

DESCRIPTION Façacryl est une peinture de dispersion acrylique de haute qualité spécialement conçue pour les façades. Très bonne adhérence sur toutes les surfaces minérales et diverses. Bon pouvoir couvrant, ne jaunit pas, respirant, parfaitement lavable et bon tendu. Rendement (indicatif) : 6-9 m²/L, selon le support Valeurs limites de l’UE pour ce produit (COV) : Cat. A/a : 30 g/L (2010). Ce produit contient moins de 30 g/L de produits COV.