Izdelki za slepa prirobnica (7)

Flansche nach DIN und ANSI: legen Sie uns bitte Ihren Bedarf vor.

Spool geschweißt mit Flansche

SAE Blanking Flange and Counterflange BFX-CP / BAS-CP ▪ 3000 PSI Standard Pressure Series (based on ISO 6162-1:2006): 1/2" (DN13) ... 5" (DN127) ▪ 6000 PSI High Pressure Series (based on ISO 6162-2:2006): 1/2" (DN13) ... 2" (DN51) ▪ Material: S355J0 / C45 or equivalent, Stainless Steel 1.4404 on request (W5) ▪ Surface: blank, oiled SAE Sandwich Plate - Female BSP Port SPL-G1/4-L ▪ e.g. for Test Couplings ▪ 3000 PSI Standard Pressure Series (based on ISO 6162-1:2006): 1/2" (DN13) ... 2" (DN51) ▪ 6000 PSI High Pressure Series (based on ISO 6162-2:2006): 1/2" (DN13) ... 2" (DN51) ▪ Materials: S355J0 / C45 or equivalent, Stainless Steel 1.4404 on request (W5) ▪ Surfaces: blank, oiled SAE Blindplug CAG-BP SAE Blindplug (High Version) CAG-BPH ▪ 3000 PSI Standard Pressure Series (acc. to ISO 6162-1:2006): 1/2" (DN13) ... 4" (DN102) ▪ 6000 PSI High Pressure Series (acc. to ISO 6162-2:2006): 1/2" (DN19) ... 2-1/2" (DN64) ▪ Materials: S355J0 / C45 or equivalent, Stainless Steel 1.4571...

Eine weitere Anschlussart bietet der Folien-Flansch, welcher mit den verschiedensten Folientypen erhältlich ist. MATERIAL Erhältlich in folgenden Materialien: PVC EPDM PIB EVA ECB FPO NENNWEITEN DN 100, DN 125 und DN 160

iglidur® flange bearing d1 [mm]: With this design it is possible to use the iglidur® high-performance bearings where housing bores with no precise tolerances are possible. When to use iglidur® flange bearings? When you want a screw flanged bearing When a clip bearing solution is not satisfactory as a sheet metal feedthrough When there is a housing with very rough tolerances When the tight fit of a press-fit bearing is not sufficient as an axial securing When not to use them? When an additional angle compensation is required igubal® flange bearing When a screw connection is not possible iglidur® clip bearing When a large guide length is necessary iglidur® G General features With this design it is possible to use the iglidur® high-performance bearings where housing bores with no precise tolerances are possible. The design enables high loads with minimum demand on the precision of the housing. iglidur® maintenance-free flange bearings are available in four materials - iglidur® G, iglidur® J, iglidur® X and iglidur® A180. Thus, with this design, a very wide range of applications - from the universal bearing through the highest wear resistance or temperature resistance (up to +250°C) up to FDA-compliant bearing solutions - can be covered. Installation Dependent on the stressing capacities, various mounting types are used. For low radial loads, it is enough to mount the iglidur® flange bearing with just two screws on a surface. For higher radial loads, it is advisable to support the iglidur® flange bearing in a bore on the reinforced side in the load direction. Large tolerances are permitted for this bore, as it is only to additionally support the iglidur® flange bearing. In order to support still higher radial loads, the iglidur® flange bearing can be press-fitted with the longer side in an H tolerance bore. The additional screw connection secures the firm seating of the bearing in the housing. For the mounting of the iglidur® maintenance-free flange bearing, no special tools or devices are necessary. The alignment of the bearing in multiple mounted shafts is easily possible at the installation. Available materials: iglidur® G, iglidur® A180, iglidur® J and iglidur® X The mounting of the iglidur® flange bearing: Simple and safe iglidur® flange bearing d1 [mm]:

Geschweißte Rohrplatte für einen Rohrbündel-Wärmetauscher

Sonderflansche: legen Sie uns bitte Ihren Bedarf vor.