Izdelki za ventil (2066)

High power solenoids of the LHS series are solenoids with strong holding forces. They are delivered with a horizontal characteristic curve. The armature is led on both sides with maintenance-free precision bearings. This results in a very high resistance to wear, granting consistent solenoid performance throughout a long service life. The LHS high performance solenoids are available in different versions. Nominal voltage:24 V Duty cycle:100 % Power consumption:26 W Stroke:12 mm Inital force:35 N End force:120 N Return spring:No  Design:No  Protection class:IP 54  Thermal class:F 155  Connection:Plug  Solenoid weight:1300 g Armature weight:250 g

Tuyau droit en acier galvanisé à bord tombés pour l’aspiration de copeaux. Épaisseur 0,8 mm. UGS:td-180 Dimensions:180 mm Diamètre section Ø (mm):180 Longueur (m):1m, 2m

High power solenoids of the LHS series are solenoids with strong holding forces. They are delivered with a horizontal characteristic curve. The armature is led on both sides with maintenance-free precision bearings. This results in a very high resistance to wear, granting consistent solenoid performance throughout a long service life. The LHS high performance solenoids are available in different versions. Nominal voltage:24 V Duty cycle:100 % Power consumption:32.9 W Stroke:15 mm Inital force:45 N End force:170 N Return spring:No Design:No  Protection class:IP 54 Thermal class:F 155 Connection:Plug Solenoid weight:2000 g Armature weight:400 g

Tuyau droit en acier galvanisé à bord tombés pour l’aspiration de copeaux. Épaisseur 0,8 mm. UGS:td-125 Dimensions:125 mm Diamètre section Ø (mm):125 Longueur (m):1m, 2m

Cônes de réduction réalisé en acier galvanisé de 0,8mm d’épaisseur. Chaque extrémité dispose d’un bord tombé permettant l’assemblage avec d’autres tuyauteries tout en garantissant un parfaite étanchéité. Ce raccordement doit se faire avec l’aide d’un collier d’assemblage. Ces cônes sont spécialement fabriqué pour réaliser des systèmes d’aspiration et de dépoussiérage industriel. UGS:cdr-160 Dimensions:160 mm

Cônes de réduction réalisé en acier galvanisé de 0,8mm d’épaisseur. Chaque extrémité dispose d’un bord tombé permettant l’assemblage avec d’autres tuyauteries tout en garantissant un parfaite étanchéité. Ce raccordement doit se faire avec l’aide d’un collier d’assemblage. Ces cônes sont spécialement fabriqué pour réaliser des systèmes d’aspiration et de dépoussiérage industriel. UGS:cdr-200 Dimensions:200 mm

MOD. VB060M

Cônes de réduction réalisé en acier galvanisé de 0,8mm d’épaisseur. Chaque extrémité dispose d’un bord tombé permettant l’assemblage avec d’autres tuyauteries tout en garantissant un parfaite étanchéité. Ce raccordement doit se faire avec l’aide d’un collier d’assemblage. Ces cônes sont spécialement fabriqué pour réaliser des systèmes d’aspiration et de dépoussiérage industriel. UGS:cdr-120 Dimensions:120 mm

Pneumatic timers are used for the precise time control of pneumatic signals in pneumatic circuits or systems. The pressure-independent function of time delay starts when pressure is applied to the control port. After the pre-selected time is elapsed, an internal 3/2 way valve is switched. The pneumatic timer is reset to the initial condition if the control port is vented for at least 300 ms. The adjustable time delay depends on the chosen version and amounts between 0.5 and 180 s. Due to its design the control pressure level must not be below working pressure level. As a result of the fire-risk evaluation according to EN 13463-1, the pneumatic timers are not subject to ATEX regulations. This means they may also be used in explosion hazardous areas as defined in IIG/ IID. Time intervall:0.5 - 60 s  Function:3/2-way NC  Pressure range:1.5 - 8 bar Type of pneumatic connection:M5  Product type:Timer  Mounting:Subplate  Medium:Compressed air, non lubricated  Ambient temperature:-10 ... +60 °C

Cônes de réduction réalisé en acier galvanisé de 0,8mm d’épaisseur. Chaque extrémité dispose d’un bord tombé permettant l’assemblage avec d’autres tuyauteries tout en garantissant un parfaite étanchéité. Ce raccordement doit se faire avec l’aide d’un collier d’assemblage. Ces cônes sont spécialement fabriqué pour réaliser des systèmes d’aspiration et de dépoussiérage industriel. UGS:cdr-150 Dimensions:150 mm

Open frame solenoid as pull type solenoid with conical face armature. Our preferred types are available in small quantities from stock. Other versions or other voltages are available on request. More information can be found in the download area. Nominal voltage:24 V Duty cycle:100 % Power consumption:6 W Stroke:8 mm Inital force:0.4 N End force:3.5 N Return spring:No  Design:No  Protection class:IP 00  Thermal class:B, 130  Connection:10 cm lead  Solenoid weight:85 g Armature weight:25 g

The LHP035 is a square linear solenoid in a robust steel housing, which can be actuated either by pushing or pulling. In general, the stroke movement is from the stroke start to the stroke end position. The electromagnet is convincing in a wide range of applications with smallest space requirements and high forces. Depending on the area of application, the LHP035 can be optimally configured. The series can be configured with different duty cycles (5, 25, 40 and 100% ED) and different stroke variants (5, 10, 15, 20 mm). The plug (= IP40), sealing ring and bellows (=IP54) provide an increased degree of protection. The reset can be carried out by means of an optional integrated spring. Special voltage variants are also available on request. Benefits at a glance: high forces with small installation space, simple mounting due to square design, short switching times, low wear, 10 million switching cycles in long-term test, wide range of configuration options Nominal voltage:24 V Duty cycle:100 % Power consumption:23.78 W Stroke:5 mm Inital force:21.9 N End force:75 N Return spring:Yes  Design:No  Protection class:IP 54 Thermal class:F 155 Connection:Leads / cable Solenoid weight:450 g Armature weight:110 g

The LHP035 is a square linear solenoid in a robust steel housing, which can be actuated either by pushing or pulling. In general, the stroke movement is from the stroke start to the stroke end position. The electromagnet is convincing in a wide range of applications with smallest space requirements and high forces. Depending on the area of application, the LHP035 can be optimally configured. The series can be configured with different duty cycles (5, 25, 40 and 100% ED) and different stroke variants (5, 10, 15, 20 mm). The plug (= IP40), sealing ring and bellows (=IP54) provide an increased degree of protection. The reset can be carried out by means of an optional integrated spring. Special voltage variants are also available on request. Benefits at a glance: high forces with small installation space, simple mounting due to square design, short switching times, low wear, 10 million switching cycles in long-term test, wide range of configuration options Nominal voltage:24 V Duty cycle:100 % Power consumption:23.78 W Stroke:5 mm Inital force:21.9 N End force:75 N Return spring:Yes  Design:No  Protection class:IP 54 Thermal class:B 130  Connection:Plug Solenoid weight:450 g Armature weight:110 g

Tuyau droit en acier galvanisé à bord tombés pour l’aspiration de copeaux. Épaisseur 1 mm. UGS:td-400 Dimensions:400 mm Diamètre section Ø (mm):400 Longueur (m):1m, 2m

Aw Horizontal Woltmann Water Meter

1/2″ FF 3/4″ FF 1″ FF 5/4″ FF 6/4″ FF 2″ FF 2 1/2″ FF 3″ FF 4″ FF 1/2″ FM 3/4″ FM 1″ FM 5/4″ FM 6/4″ FM 2″ FM

Tuyau droit en acier galvanisé à bord tombés pour l’aspiration de copeaux. Épaisseur 0,8 mm. UGS:td-120 Dimensions:120 mm Diamètre section Ø (mm):120 Longueur (m):1m, 2m

Coude embouti en acier galvanisé de rayon R=1,5D avec bord tombé. Ce type de coude est utilisé pour l’installation d’un système de dépoussiérage industriel ou d’aspiration pour menuiserie. UGS:c-100 Dimensions:100 mm Angle:15°, 30°, 45°, 60°, 90°

Coude segmenté en acier galvanisé de rayon R=1,5D avec bord tombé. Ce type de coude est utilisé pour l’installation d’un système de dépoussiérage industriel ou d’aspiration pour menuiserie. UGS:c-225 Dimensions:225 mm Angle:15°, 30°, 45°, 60°, 90°

Nos tables aspirantes pour le ponçage peuvent être raccordées directement au système d'aspiration industrielle existant ou peuvent être autonome. Le plan de travail, réalisé en tôle d’acier emboutie de forme trapézoïdale avec ouvertures d’aspiration des poussières est conçu de façon à assurer une dépression uniforme sur toute la surface lorsque le système d’aspiration est en marche. L’aspiration des poussières est alors optimale.

Les silos pour copeaux de bois sont construits à l’aide de panneaux cintrés, boulonnés de l’extérieur pour de meilleures performances. Ils ont l’avantage d’être modulaires et évolutifs en fonction de vos besoins. L’utilisation d’un silo en acier par rapport au béton présente de nombreux avantages

Le ventilateur est le cœur du système d'aspiration industrielle, il est déterminant pour le rendement et les coûts d'exploitation de l'installation. La turbine en acier est conçue pour une pression d’air et de sortie spécifiée, et est à la fois équilibrée statiquement et dynamiquement. Les ventilateurs radiaux ont une construction robuste pour une longue vie et une faible maintenance. La haute efficacité du ventilateur assure de faibles coûts de fonctionnement. Ventilateur centrifuge basse, moyenne ou haute pression pour traitement de l’air industriel.

The door holding magnets are mainly used as holding devices on fire protection doors. They hold them in place when open. Controlled by a fire alarm or smoke protection control panel, they release the closures by interrupting the power supply in the event of a fire hazard. Product features: - Coil vacuum encapsulated (IP65) - VdS quality-controlled - Tested according to EN1155 & EN 14637 - Optimised design and quality - Accessories: Anchor plate Nominal voltage:24 V Duty cycle:100 % Power consumption:1.5 W Holding force:300 N Design:Without base plate  Connection:terminal clamp 

The door holding magnets are mainly used as holding devices on fire protection doors. They hold them in place when open. Controlled by a fire alarm or smoke protection control panel, they release the closures by interrupting the power supply in the event of a fire hazard. Product features: - Coil vacuum encapsulated (IP65) - VdS quality-controlled - Tested according to EN1155 & EN 14637 - Optimised design and quality - Accessories: Anchor plate Nominal voltage:24 V Duty cycle:100 % Power consumption:1.5 W Holding force:490 N Design:Wall mounting  Connection:terminal clamp 

The new Kuhnke Vico 04 series is a powerful display unit with an industrial design and enables modern operating concepts. The installed CODESYS PLC software package offers the possibility to use control functions in addition to visualisation. The visualisation is developed together with the PLC application in the free CODESYS Development System. The device communicates with the external fieldbus components via EtherCAT, OPC UA and Modbus. The Kuhnke Vico 04 series is based on a powerful ARM Cortex-A8 processor combined with a resistive touch display. All components are robust and have long-term availability. Configuration:HMI with control function  Function:HMI with control function  Model:Panel mounted device  Product status:Standard product  Display:4.3" wide  Resolution:480 x 272 (PSP)  Processor:ARM Cortex-A8 - 1 Ghz  Operating system:Linux  Software:CODESYS V3 Soft PLC, TargetVisu, WebVisu  Main memory:512 Non-volatile memory:Flash Data Memory:Flash Dive:Flash disk 4 GB  Interfaces:1 x Ethernet 10/100Mbit, 1 x RS-232, 1 x USB 2.0 host, max 500 mA Field bus interfaces:Modbus RTU, Modbus TCP, EtherCAT, OPC UA  Housing material:plastic body with black, seamless film cover Dimensions (W x H x D):107 x 147 x 34 mm  Supply voltage:24 VDC / (10 VDC … 32 VDC)  Temperature range:0 ... +55°C 

The robust OAC vibratory feeder coil series consists of a UI core and two excitation windings connected in series. Continuous controllability via drive voltage and/or frequency, high power ratings and optimally minimized eddy current losses characterize the electromagnet. The direction of oscillation is achieved by the geometric arrangement of the springs. The useful oscillation amplitude corresponds to twice the amplitude of the oscillation frequency of the overall system. OAC oscillating solenoids from Kendrion are used in spring mass systems to generate directional, linear oscillating movements. The vibratory feeder coil is available in 16 different sizes with universal mounting options and is supplied without a spring mass system. On request, the OAC series are also available with a base plate for mounting or a KTL coating for increased corrosion protection. Nominal voltage:230 V Apparent Power:15 VA Nominal air gap:2 mm Oscillating frequency:6000  Length:29 mm Width:42 mm Height:42 mm Dimensions:29,42,42  Thermal class:Y 90 

CODESYS Starterkit Control & Motion Easy positioning. The starter kit is fully wired and ready for use within minutes. In our download area, you can easily download a set of detailed examples explaining how to write your program and how to load it onto the control unit. Function:CODESYS Starterkit Control & Motion  Model:Ready to use functional unit  Integrated function:CODESYS V3 PLC with EtherCAT Expansion module 16DI/16DO, EtherCAT® motion controller for stepper and Software:CODESYS V3 Soft PLC, CODESYS , CODESYS WebVisu, Motion Control Library  Interfaces:LAN, RS-232, CAN, USB  Field bus interfaces:CANopen, Modbus RTU, Modbus TCP, EtherCAT, OPC UA  Product status:Standard product 

The controller is a fieldbus device for the control of up to 7 power modules from the modular heating System from Kendrion, which are directly connected via the module bus. In addition to system monitoring, the controller can also control or regulate the individual output channels of all power modules. Actual temperature values can be delivered directly via CAN fieldbus or provided by a higher-level controller e.g. a PLC. Functions:Temperature control, system monitoring, fieldbus communication, bus coupler for up to 7 MHS power mo Field bus interfaces:EtherCAT  Interfaces:1 x Ethernet 10/100Mbit (on request)  Modul bus:Data communication via CAN, electronic supply 24 VDC  Status indication:Heating system, EtherCAT, CANopen, DC power supply  Integrated I/Os:on request: 8 x DI: input delay: 3 ms / 8 x DO 24V, 0,5 A, Short circuit protection  Housing material:module made of steel with stainless steel cover for use in a closed, metallic control cabinet  IP-Protection Class:IP 20  Mounting:Prepared for left-side mounting on the power module  Dimensions (W x H x D):451 mm x 44 mm x 286 mm  Supply voltage:24 VDC / -10% +10% (21,6 V – 26,4)  Operating temperature:In vertical installation position: 0°C ... 35°C  Certifications:CE, cULus (in preparation) 

Based on our smallest rotary solenoid D1, Kendrion offers a compact miniature shutter in the field of optical safety technology. The D16 shutter is characterized above all by its high reliability and long service life of 2.5 million switching cycles. In addition, this shutter has a fast closing time of less than 20 ms. Rotation angle:65°  Return mechanism:Spring return  End position detection:No Housing type:round  Nominal voltage:12V DC V Duty cycle:100% ED % Power consumption:2,4 W W Thermal class:B (130 °C)  Connection:Wire 20 cm  Dimensions:Durchmesser 15 / Länge 20 mm  Switching time:≤ 20 ms ms Switching frequency:max. 5 Hz Hz

Holding magnet for holding or clamping ferromagnetic workpieces. The DC-excited coil achieves a holding force of up to 30,000 N when energized. When the supply voltage is switched off, the workpiece to be held falls off. The holding solenoid is maintenance-free and are characterized by a low operating current at high holding forces. The holding solenoid is available in different sizes in round, flat or square design. Nominal voltage:24 V Duty cycle:100 % Power consumption:2.2 W Holding force:112 N Diameter:20x15 mm