Izdelki za ventil (1211)

The simple and compact design of this miniature PE converter with fixed switch-on pressure of 0.8 bar allows its use in various applications such as medical technology, dental treatment units, robotics, analysis systems, process and safety engineering. Easy mounting and high functional reliability are other advantages. By using silver contacts a long lifetime can be ensured even at high switching frequencies. As a result of the fire-risk evaluation according to EN 13463-1, the pneumatic timers are not subject to ATEX regulations. This means they may also be used in explosion hazardous areas as defined in IIG/ IID. Time intervall:3 - 100 s  Function:5/2-way  Pressure range:0 - 10 bar Type of pneumatic connection:M5  Ambient temperature:-10 ... +60 °C

The door holding magnets are mainly used as holding devices on fire protection doors. They hold them in place when open. Controlled by a fire alarm or smoke protection control panel, they release the closures by interrupting the power supply in the event of a fire hazard. Product features: - Coil vacuum encapsulated (IP65) - VdS quality-controlled - Tested according to EN1155 & EN 14637 - Optimised design and quality - Accessories: Anchor plate Nominal voltage:24 V Duty cycle:100 % Power consumption:1.5 W Holding force:490 N Design:with steel base plate  Connection:terminal clamp 

The robust OAC vibratory feeder coil series consists of a UI core and two excitation windings connected in series. Continuous controllability via drive voltage and/or frequency, high power ratings and optimally minimized eddy current losses characterize the electromagnet. The direction of oscillation is achieved by the geometric arrangement of the springs. The useful oscillation amplitude corresponds to twice the amplitude of the oscillation frequency of the overall system. OAC oscillating solenoids from Kendrion are used in spring mass systems to generate directional, linear oscillating movements. Nominal voltage:230 V Apparent Power:100 VA Nominal air gap:1.5 mm Oscillating frequency:6000  Length:31 mm Width:60.5 mm Height:60 mm Dimensions:31,60.5,60  Thermal class:Y 90 

Les distributeurs sont des composants permettant d'isoler ou de véhiculer des liquides ou des gaz. Nous proposons différents distributeurs, nourrices de distribution, pièces de distribution à sorties multiples et répartiteurs.

Kuhnkes FIO Safety SDI8/SDO2 is a safety I/O terminal featuring eight safe digital input channels and two safe digital output channels. This expansion module from Kuhnke's FIO range easily integrates in any EtherCAT® network. Eight inputs pick up sensor readings via floating 24 VDC contacts while two outputs send up to 0.5 A of current per channel to 24 VDC actuators. In case the EtherCAT terminal detects a fault it changes to a safe state (fail safe). The module meets the requirements of IEC 61508 SIL3 and DIN EN ISO 13849 PL e. Function:functional safety IO  Model:Control cabinet module  Digital I/Os (integrated):safe inputs: 8 SDI / safe outputs: 2 SDO 0.5A (OSSD)  Field bus interfaces:EtherCAT / FSoE  Type of connection:female plug with PUSH IN spring connection  Status indication:LEDs allocated to the point of termination Dimensions (W x H x D):25 x 120 x 90 mm  Supply voltage:24 (-20% / +25%) VDC 

Holding magnet for holding or clamping ferromagnetic workpieces. The DC-excited coil achieves a holding force of up to 30,000 N when energized. When the supply voltage is switched off, the workpiece to be held falls off. The holding solenoid is maintenance-free and are characterized by a low operating current at high holding forces. Nominal voltage:24 V Duty cycle:100 % Power consumption:45.7 W Holding force:7200 N Design:round  Diameter:602,31,32  Holding permanentmagnetic?:no  Thermal class:E 120 Connection:terminal clamp 

The advanced laser shutter DS200X8 combines with its short closing time of less than 15 ms. a long mechanical service life with the possibility of detecting the position and monitoring the mirror temperature. When the shutter is closed, the laser beam is absorbed in the beam trap. A laser power of up to 100 W is possible. Rotation angle:30°  Return mechanism:Spring return  End position detection:Yes  Housing type:round Nominal voltage:12V DC / 24V DC optional V Duty cycle:100% ED % Power consumption:4 W / 6V DC holding voltage W Thermal class:B (130 °C)  Connection:Wire 20 cm  Dimensions:100 x 60 x 100mm  Switching time:≤ 15 ms ms Switching frequency:max. 5 Hz Hz

CODESYS Starterkit Control & Visualization Control, communication and visualization in one device The starter kit is fully wired and ready for use within minutes. In our download area, you can easily download a set of detailed examples explaining how to write your program, set up the visualization and load it onto to the control unit. Function:CODESYS Starterkit Control & Visualization  Model:Ready to use functional unit  Integrated function:Panel PLC 7", EtherCAT® IO with 16 inputs and 16 outputs  Software:CODESYS V3 Soft PLC, CODESYS TargetVisu, CODESYS WebVisu  Interfaces:2 x LAN, RS-232, RS-485, 2 x CAN, USB  Field bus interfaces:2 x CANopen, Modbus RTU, Modbus TCP, EtherCAT, OPC UA  Product status:Standard product 

Kuhnkes FIO Safety SDI16/SDO2 is a safety I/O terminal featuring 16 safe digital input channels and four safe digital output channels. This expansion module from Kuhnke's FIO range easily integrates in any EtherCAT® network. 16 inputs pick up sensor readings via floating 24 VDC contacts while four outputs send up to 0.5 A of current per channel to 24 VDC actuators. In case the EtherCAT terminal detects a fault it changes to a safe state (fail safe). The module meets the requirements of IEC 61508 SIL3 and DIN EN ISO 13849 PL e. ; Safety over EtherCAT (FSoE); 16 safe inputs 24 VDC; 4 safe outputs 0.5 A; IEC 61508 SIL3 and DIN EN ISO 13849 PL e Function:functional safety IO  Model:Control cabinet module  Digital I/Os (integrated):safe inputs: 16 SDI / safe outputs: 4 SDO 0.5A (OSSD)  Product status:Standard product  Field bus interfaces:EtherCAT / FSoE  Type of connection:female plug with PUSH IN spring connection  Status indication:LEDs allocated to the point of termination  Housing material:Aluminium frame, plastic housing  Dimensions (W x H x D):25 x 120 x 90 mm  IP-Protection Class:IP 20  Supply voltage:24 (-20% / +25%) VDC  Operating temperature:0 ... +55  Immunity:Zone B according to EN 61131-8  Certifications:CE, UL 

The door holding magnets are mainly used as holding devices on fire protection doors. They hold them in place when open. Controlled by a fire alarm or smoke protection control panel, they release the closures by interrupting the power supply in the event of a fire hazard. Product features: - Coil vacuum encapsulated (IP65) - VdS quality-controlled - Tested according to EN1155 & EN 14637 - Optimised design and quality - Accessories: Anchor plate Nominal voltage:24 V Duty cycle:100 % Power consumption:1.5 W Holding force:1372 N Design:With base plate, micro switch  Connection:terminal clamp 

Based on our rotary solenoid D2, Kendrion offers a wide range of highly reliable optical shutters for blocking light and laser beams in the field of optical safety technology. The optical shutter D23 forms the technical basis with remarkable properties and can be used in a wide range of applications, e.g. in medical instruments, aeronautical instruments, fiber optic signal transmission systems and in mass photometry. The D23 optical shutter impresses with maximum reliability, durability and a fast switching time of approx. 15 ms. With at least 10 million switching cycles, the Shutter D23 is designed for reliable continuous operation. Rotation angle:30°  Return mechanism:Spring return  End position detection:Yes  Housing type:round  Nominal voltage:24V DC / 12V DC optional V Duty cycle:100% ED % Power consumption:3,8 W W Thermal class:B (130 °C)  Connection:Wire 20 cm  Dimensions:Durchmesser 27,6 / Länge 42mm  Switching time:≤ 15 ms ms Switching frequency:max. 5 Hz Hz

The permanent holding magnets achieve a holding force of up to 35,000 N in the de-energized state and are designed for long holding of magnetic workpieces. When the DC-excited coil is switched on, the permanent magnetic field on the holding surface is neutralized and the workpiece to be held can be removed. The electromagnet holds loads even in the event of a power failure and only needs to be energized briefly to release the workpiece. It is characterized by its energy efficiency and high holding forces. The permanent holding solenoids are available in different sizes with forces between 8 and 3,500 N. Nominal voltage:24 V Duty cycle:100 % Power consumption:6.2 W Holding force:260 N Design:round Diameter:32x40 mm Holding permanentmagnetic?:Yes  Thermal class:E 120 Connection:free leads 200mm 

The new Vico MT series is a powerful display unit with multi-touch technology in an industrial-grade unit design. The installed CODESYS HMI software package makes it possible to visualise data from any CODESYS controller(s) on the remote Vico MT. The visualisation is developed either independently or together with the PLC application in the free CODESYS Development System. The devices with brilliant IPS display have a robust glass touch screen with an aluminium bezel and are prepared for easy installation in the control cabinet. All components are robust and have long-term availability. ; High quality industrial design; IPS widescreen display with multi-touch glass touch; Visualisation with the CODESYS Development System; High performance and long-term availability Configuration:CODESYS HMI  Function:Multi-Touch Panel, CODESYS V3 HMI  Model:Panel mounted HMI  Product status:Standard product  Display:10.1" wide, IPS  Resolution:1280 x 800 / (16:10)  Processor:i.MX8M mini Quad-Core CPU; 4 x 1.6 GHz  Operating system:Linux  Main memory:1 GB  Drive:4 GB eMMC memory, 2 MB NOR Flash, µSD Slot  Interfaces:2 x LAN, 2 x USB, 1 x RS-232  Housing material:Aluminum frame with glass front  Data memory:Flash disk 4 GB  Dimensions (W x H x D):265 x 187 x 41 mm  IP-Protection Class:IP 65 / IP 20  Supply voltage:24 VDC (± 20 %)  Temperature range:0 ... +55°C 

Holding magnet for holding or clamping ferromagnetic workpieces. The DC-excited coil achieves a holding force of up to 30,000 N when energized. When the supply voltage is switched off, the workpiece to be held falls off. The holding solenoid is maintenance-free and are characterized by a low operating current at high holding forces. The holding solenoid is available in different sizes in round, flat or square design. Nominal voltage:24 V Duty cycle:100 % Power consumption:90 W Holding force:3000 N Design:round Diameter:250x80 mm Holding permanentmagnetic?:no Thermal class:B 130 Connection:cable 300mm 

Holding magnet for holding or clamping ferromagnetic workpieces. The DC-excited coil achieves a holding force of up to 30,000 N when energized. When the supply voltage is switched off, the workpiece to be held falls off. The holding solenoid is maintenance-free and are characterized by a low operating current at high holding forces. Nominal voltage:24 V Duty cycle:100 % Power consumption:6.5 W Holding force:880 N Design:square Dimensions:100,31,32  Holding permanentmagnetic?:no  Thermal class:E 120 Connection:terminal clamp 

The controller is a fieldbus device for the control of up to 7 power modules from the modular heating System from Kendrion, which are directly connected via the module bus. In addition to system monitoring, the controller can also control or regulate the individual output channels of all power modules. Actual temperature values can be delivered directly via CAN fieldbus or provided by a higher-level controller e.g. a PLC. Functions:Temperature control, system monitoring, fieldbus communication, bus coupler for up to 7 MHS power mo Field bus interfaces:CANopen Interfaces:1 x Ethernet 10/100Mbit (on request)  Modul bus:Data communication via CAN, electronic supply 24 VDC  Status indication:Heating system, EtherCAT, CANopen, DC power supply  Integrated I/Os:on request: 8 x DI: input delay: 3 ms / 8 x DO 24V, 0,5 A, Short circuit protection  Housing material:module made of steel with stainless steel cover for use in a closed, metallic control cabinet  IP-Protection Class:IP 20  Mounting:Prepared for left-side mounting on the power module  Dimensions (W x H x D):451 mm x 44 mm x 286 mm  Supply voltage:24 VDC / -10% +10% (21,6 V – 26,4)  Operating temperature:In vertical installation position: 0°C ... 35°C  Certifications:CE, cULus (in preparation) 

ODESYS Starterkit Control & OPC UA Easy programming. The starter kit is fully wired and ready for use within minutes. In our download area, you can easily download a set of detailed examples explaining how to write your program and how to load it onto the control unit. ; "Ready to use" ; Easy to integrate into a machine / plant ; Individually expandable and scalable ; Universally applicable thanks to standardised hardware and software interfaces Function:Starterkit Control & OPC UA  Model:Ready to use functional unit  Integrated function:CODESYS V3 PLC with EtherCAT Expansion module 16DI/16DO  Software:CODESYS V3 Soft PLC, CODESYS WebVisu  Interfaces:LAN, RS-232, CAN, USB  Field bus interfaces:CANopen, Modbus RTU, Modbus TCP, EtherCAT, OPC UA  Product status:Standard product 

The door holding magnets are mainly used as holding devices on fire protection doors. They hold them in place when open. Controlled by a fire alarm or smoke protection control panel, they release the closures by interrupting the power supply in the event of a fire hazard. Product features: - Coil vacuum encapsulated (IP65) - VdS quality-controlled - Tested according to EN1155 & EN 14637 - Optimised design and quality - Accessories: Anchor plate Nominal voltage:24 V Duty cycle:100 % Power consumption:3 W Holding force:588 N Design:EX-protected Zone 21/22  Connection:Free leads 

The simple and compact design of this miniature PE converter with fixed switch-on pressure of 0.8 bar allows its use in various applications such as medical technology, dental treatment units, robotics, analysis systems, process and safety engineering. Easy mounting and high functional reliability are other advantages. By using silver contacts a long lifetime can be ensured even at high switching frequencies. As a result of the fire-risk evaluation according to EN 13463-1, the pneumatic timers are not subject to ATEX regulations. This means they may also be used in explosion hazardous areas as defined in IIG/ IID. Time intervall:3 - 100 s  Function:5/2-way  Pressure range:0 - 10 bar Type of pneumatic connection:M5  Ambient temperature:-10 ... +60 °C

The robust OAC vibratory feeder coil series consists of a UI core and two excitation windings connected in series. Continuous controllability via drive voltage and/or frequency, high power ratings and optimally minimized eddy current losses characterize the electromagnet. The direction of oscillation is achieved by the geometric arrangement of the springs. The useful oscillation amplitude corresponds to twice the amplitude of the oscillation frequency of the overall system. OAC oscillating solenoids from Kendrion are used in spring mass systems to generate directional, linear oscillating movements. The vibratory feeder coil is available in 16 different sizes with universal mounting options and is supplied without a spring mass system. On request, the OAC series are also available with a base plate for mounting or a KTL coating for increased corrosion protection. Nominal voltage:230 V Apparent Power:282 VA Nominal air gap:3 mm Oscillating frequency:6000  Length:56 mm Width:90 mm Height:88 mm Dimensions:56,90,88  Thermal class:Y 90 

Flat gripper with a samarium-cobalt magnet in a steel pot. The housing increases the adhesive force of the permanent magnet. The maximum adhesive force is achieved when the entire surface is placed on a metallic surface. The flat gripper has a threaded socket with an internal thread. Design:with threaded bush  Material:SmCo  Force:90 N Diameter:20 mm Height:6 mm Total height:13 mm Diameter threaded bush:8 mm Thread:M4 Weight:16 g Temperature:200 °C Housing:galvanized 

Holding magnet for holding or clamping ferromagnetic workpieces. The DC-excited coil achieves a holding force of up to 30,000 N when energized. When the supply voltage is switched off, the workpiece to be held falls off. The holding solenoid is maintenance-free and are characterized by a low operating current at high holding forces. Nominal voltage:24 V Duty cycle:100 % Power consumption:2.2 W Holding force:112 N Design:round  Diameter:20x15 mm Holding permanentmagnetic?:no  Thermal class:B 130  Connection:free leads 200mm 

The new Vico MT series comprises powerful display units with multi-touch technology in an industrial-grade unit design.The installed CODESYS PLC software package makes it possible to use control functions in addition to visualization. The visualization is developed together with the PLC application in the free CODESYS Development System.The device communicates with the external fieldbus components via EtherCAT and Modbus.The devices with brilliant IPS display have a robust glass touch screen with an aluminium bezel and are prepared for easy installation in the control cabinet. All components are robust and have long-term available. Configuration:CODESYS HMI  Function:Multi-Touch HMI with control function Model:Panel mounted HMI  Product status:Standard product  Display:15.6" wide, IPS  Resolution:1366 x 768 / (16:9)  Processor:Arm® i.MX8M Mini ; 4 Cores ; 1.2 GHz  Operating system:Linux  Software:CODESYS V3 Soft PLC, TargetVisu, WebVisu  Main memory:1 GB Drive: 4 GB eMMC memory, 2 MB NOR Flash, µSD Slot Interfaces:2 x LAN, 2 x USB, 1 x RS-232  Field bus interfaces:Modbus RTU, Modbus TCP, EtherCAT, OPC UA  Housing material:Aluminum frame with glass front  Dimensions (W x H x D):405 x 254 x 60 mm  IP-Protection Class:IP 65 / IP 20  Supply voltage:24 V DC (± 20%)  Temperature range:0 ... +55°C 

CODESYS Starterkit HMI Extension Easy visualization. Each Kuhnke CODESYS Starterkit can easily be extended by a CODESYS HMI Touch display. Only connect the display to the Starterkit via an Ethernet cable, connect in with power supply and download a project on the HMI device. The programming, the connection of the program with the PLC as well as the steps to create an own visualization are explained in detail by several examples that can be downloaded comfortably in our download area. Function:CODESYS Starterkit HMI Extension  Model:Ready to use functional unit  Integrated function:Touchsccreen, TFT color display, IP 65 Front  Software:CODESYS HMI  Interfaces:LAN, RS-232 Field bus interfaces:HMI  Product status:Standard product 

Kann abwechselnd mit Zumessventilen und Progressivverteiler arbeiten Pumpe: Fördermenge 10ml/min Förderdruck 100bar (Überdruckventil) Leistung DC24V: Motor 20W/0.8A Pressure relief solenoid 26W/1.1A Total 46W/1.9A Einschaltzeit: Max. ON time: 7.5 min. Einschaltdauer: Max.25% (20°C) Medium Konsistenz: Cartridge Grease No.000,00,0,1 Erforderliches Fett MP0, FS2, MT1 Kartuschengrösse: 700ml cartridge Gewicht: 2,6kg (7C) Druckentlastung: eingebaut Inklusive 1St. Kartusche FS2 700cc Pumpe:Fördermenge 10ml/min Einschaltzeit:Max. ON time: 7.5 min. Einschaltdauer:Max.25% (20°C) Medium Konsistenz:Cartridge Grease No.000,00,0,1 Erforderliches Fett MP0, FS2, MT1 Kartuschengrösse:700ml cartridge Gewicht:2,6kg (7C) Druckentlastung:eingebaut Artikelnummer:1028620

The digital Kuhnke FIO I/O modules relay the binary control signals to the actuators and analyze the input signals of the automation device galvanically separated from the process level. The Kuhnke FIO DI16 / DO16 module has 16 outputs, each output can be loaded with up to 0.5A. In addition the module offers 16 inputs with an input delay of 1ms. The primary and secondary sides of the module are separated by optocouplers. This galvanic decoupling makes it possible to switch off the supply of the outputs via only one safety component. The signal status of each channel is indicated by LEDs. The generation of a variant that supports distributed clocks is possible on request. ; 16 digital inputs for 24 VD with input filter 1 ms640 200 209 022 400; 16 short-circuit-proof outputs with output current up to 0.5 A; Status display locally assigned to the terminal point; Fast connection with PUSH-IN spring connection Function:Digital IN, Digital OUT  Model:Control cabinet modul  Digital I/Os (integrated):inputs: 16 DI 1ms / outputs: 16 DO 0.5A  Product status:Standard product  Field bus interfaces:EtherCAT  Type of connection:female plug with PUSH IN spring connection  Status indication:LEDs allocated to the point of termination  Housing material:Aluminium frame, plastic housing  Dimensions (W x H x D):25 x 120 x 90 mm  IP-Protection Class:IP 20  Supply voltage:24 V (-20% / +25%)  Operating temperature:0 ... +55°C  Immunity:Zone B according to EN 61131-2  Certifications:CE, UL 

T-piece with expanded outlet

The fanless PLC with iMX6 Quad Core processor technology combines compactness with longevity and performance. The device has an integrated flash disk and an easily accessible SD card slot. USB interfaces allow the use of additional change-over memories or external peripherals.  ; Kuhnke controllers with CODESYS SoftMotion CNC+Robotocs provide the user with extensive project planning options for his motion tasks. Among other things, certified motion modules according to PLCopen and the full scope of the IEC 61131-3 programming interface are available, as well as integrated motion planning with coordinate values for robot positions in different coordinate systems and numerous supported kinematics with convenient configuration, e.g. various gantry robots (2/3/5 axes), bipod/tripod robots, Scara robots. ; Fanless  i.MX6-QuadCore processor technology ; Stable, compact housing, DIN-rail mounting ; CODESYS Soft PLC with WebVisu and SoftMotion CNC+Robotics Configuration:CODESYS Compact PLC  Function:Compact CODESYS PLC  Model:Control cabinet modul  Product status:Standard product  Processor:Freescale i.MX6X Quad Core; 1 GHz  Operating system:Linux RT  Software:CODESYS V3 Soft PLC, WebVisu, Softmotion CNC+Robotics  Main memory:1024 MB RAM  Non-volatile memory:Stored in flash memory  Data memory:SD-Karte / 4GB eMMC  Drive:Flash disk 256 MB  Interfaces:EtherCAT, OPC UA, CANopen, Modbus TCP/RTU  Field bus interfaces:EtherCAT, OPC UA, CANopen, Modbus TCP/RTU  Housing material:Stainless steel, heat sink made of aluminum  Mounting:DIN-rail mounting  Dimensions (W x H x D):50 x 190 x 115 mm 

The door holding magnets are mainly used as holding devices on fire protection doors. They hold them in place when open. Controlled by a fire alarm or smoke protection control panel, they release the closures by interrupting the power supply in the event of a fire hazard. Product features: - Coil vacuum encapsulated (IP65) - VdS quality-controlled - Tested according to EN1155 & EN 14637 - Optimised design and quality - Accessories: Anchor plate Nominal voltage:24 V Duty cycle:100 % Power consumption:1.5 W Holding force:490 N Design:Plastic swivel head 150/175 mm  Connection:terminal clamp 

Flat gripper with a neodymium magnet in a steel pot. The housing increases the adhesive force of the permanent magnet. The maximum adhesive force is achieved when the entire surface is placed on a metallic surface. The flat gripper has no hole and is usually glued or pressed in. Design:with threaded bush  Material:NdFeB  Force:60 N Diameter:13 mm Height:4.5 mm Weight:4.5 g Temperature:80 °C Housing:galvanized